If it is determined that the optical axis of the forward recognition camera has deviated, DTC C1AA8 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA8 | Front Camera Module Incorrect Axial Gap | After the ignition switch is turned to ON for 3 seconds or more and the forward recognition camera detects forward recognition camera axis deviated. | ·
Forward recognition camera ·
Windshield glass ·
Wheel alignment |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the forward recognition camera may not operate properly due to a difference in the transmissivity or black ceramic border.
Forward recognition camera optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.
Forward recognition camera optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The forward recognition camera optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.
Check the operating conditions of the vehicle.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or being towed | A |
| Vehicle is overloaded or being towed | B |
A
B
Check the front and rear wheel alignment (toe).
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 3 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA8 is not output | A |
| DTC C1AA8 is output | B |
A
B
Check the installation condition of the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION
If there is a malfunction with the installation condition of the forward recognition camera, replace the windshield glass.
No deformation or deviation in forward recognition camera installation bracket.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the windshield glass.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal.
Perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the ignition switch to ON and wait 3 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA8 is not output | A |
| DTC C1AA8 is output | B |
A
B
Check the front and rear wheel alignment (toe).
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Check the installation condition of the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION
If there is a malfunction with the installation condition of the forward recognition camera, replace the windshield glass.
No deformation or deviation in forward recognition camera installation bracket.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the windshield glass.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT