Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › THROTTLE BODY › from 2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328589 THROTTLE BODY A

A25A-FKS ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A402360C01
1.177,0.823 0.906,0.25 0.906,0.25 2.021,0.531 true 0.656,0.156 0.885,0.365 0.229,0.208 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusions of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.



a.
A402359C01
2.76,1.708 2.76,1.417 true 2.563,1.75 2.875,1.906 0.313,0.156 10 false *c 3.104,1.073 3.417,1.229 0.313,0.156 10 false *a 3.198,1.271 3.396,1.5 0.198,0.229 10 false *b 3.104,1.51 3.417,1.667 0.313,0.156 10 false *a 2.708,1.698 3.021,1.854 0.313,0.156 10 false *d
*a 45°(Claw of Clip Location)
*b Left of Vehicle
*c Front of Vehicle
*d Paint Mark


Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

If the throttle body with motor assembly has been struck or dropped, replace it.

·

Make sure to position the clip as shown in the illustration.




b.
A402357C01
2.667,1.573 2.885,1.156 2.885,1.156 3.052,1.156 true 2.49,0.958 2.802,1.115 0.313,0.156 10 false *a 3.052,1.667 3.365,1.823 0.313,0.156 10 false *c 3.125,1.406 3.323,1.625 0.198,0.219 10 false *b 2.74,1.958 3.052,2.115 0.313,0.156 10 false *c 3.083,1.063 3.281,1.281 0.198,0.219 10 false *d
*a Top
*b Rear of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Using an 8 mm socket wrench, install the throttle body with motor assembly to the intake manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 6 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.

Connect the throttle body with motor assembly connector.


Hide 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A402354C01
0.583,3.844 0.833,3.375 0.833,3.375 1,3.375 true 1.104,4.281 1.104,4.031 1.104,4.031 1.229,3.865 true 1.031,3.292 1.344,3.448 0.313,0.156 10 false *a 1.052,4.281 1.365,4.438 0.313,0.156 10 false *b 2.927,3.26 3.24,3.417 0.313,0.156 10 false *c 2.083,4.229 2.396,4.385 0.313,0.156 10 false *d 1.031,0.115 1.344,0.271 0.313,0.156 10 false *e 1.927,0.135 2.24,0.292 0.313,0.156 10 false *f
*a Protrusion
*b Cutout
*c Top
*d Front of Vehicle
*e Locked
*f Unlocked


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly and unlock the hose clip to secure it as shown in the illustration.

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.



b.

Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


c.

Engage the 2 air cleaner cap clamps.


d.
A402355C01
0.844,1.26 0.948,1.083 0.948,1.083 1.063,1.083 true 0.75,0.844 1.063,1 0.313,0.156 10 false *a 0.104,1.323 0.417,1.479 0.313,0.156 10 false *b 0.188,1.104 0.5,1.26 0.313,0.156 10 false *c 0.188,1.542 0.5,1.698 0.313,0.156 10 false *c 1.094,0.99 1.406,1.146 0.313,0.156 10 false *d
*a Top
*b Front of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



e.

Connect the vacuum hose to the air cleaner hose.


f.

Engage the 2 wire harness clamps.


g.

Connect the mass air flow meter sub-assembly connector.


Hide 12601B 4.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 5.ADD ENGINE COOLANT

Hide 7.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372


f.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




g.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage %.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage %
50003 372 216

h.

According to the display on the GTS, read the Data List while fully depressing the accelerator pedal and check that the value is 60% or higher.


i.

Perform a road test and confirm that there are no abnormalities.