Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › ECM › 2017.12–2018.04
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328593 ECM A

A25A-FKS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53295E 2.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 4.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 5.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 89661 6.REMOVE ECM

a.
A402361

Rotate the 3 levers while pushing the locks, and disconnect the 3 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A402363

Remove the 2 bolts, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 7.REMOVE NO. 1 ECM BRACKET

a.
A402364

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 8.REMOVE NO. 2 ECM BRACKET

a.
A402365

Remove the 2 screws and No. 2 ECM bracket from the ECM.