Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › 2017.12–2020.08
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0319392 FUEL INJECTOR(for Port Injection) A

A25A-FKS FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23250F 1.INSTALL PORT FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a port fuel injector assembly.



a.

Apply a light coat of spindle oil or gasoline to 4 new O-rings, and install one to each port fuel injector assembly.

NOTICE:

Check that there is no damage or foreign matter on the groove of the port fuel injector assembly when installing the O-ring to each port fuel injector assembly.



b.
A401656C01
1.531,1.76 1.75,1.76 1.75,1.76 2.198,1.385 true 2.281,1.271 2.458,1.104 2.458,1.104 2.604,1.104 false 2.281,1.385 2.521,1.281 2.521,1.281 2.677,1.281 false 2.719,1.198 3.031,1.354 0.313,0.156 10 false *a 1.365,1.677 1.677,1.833 0.313,0.156 10 false *b 2.656,1.021 2.969,1.177 0.313,0.156 10 false *b
*a Stopper
*b Claw


Install the 4 port fuel injector assemblies to the fuel delivery pipe with sensor assembly.

NOTICE:
·

Make sure that the port fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the port fuel injector assembly installation holes of the fuel delivery pipe with sensor assembly are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the port fuel injector assembly.




Hide 82125N 2.INSTALL NO. 5 ENGINE WIRE

a.

Engage the 2 clamps to install the No. 5 engine wire to the fuel delivery pipe with sensor assembly.


b.

Connect the 4 port fuel injector assembly connectors and fuel pressure sensor connector.


Hide 23291 3.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23807V 4.INSTALL NO. 1 DELIVERY PIPE SPACER

a.

Install the 2 No. 1 delivery pipe spacers to the cylinder head sub-assembly.


Hide 23800 5.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.

Place the fuel delivery pipe with sensor assembly with the 4 port fuel injector assemblies onto the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when installing the fuel delivery pipe with sensor assembly.



b.

Install the fuel delivery pipe with sensor assembly with the port fuel injector assemblies with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 23910A 6.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


Hide 23801P 7.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23801P 9.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 13.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a port fuel injector assembly.