Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING RECEIVER › 2017.12–2018.04
RM33A0E _53 Suspension _065363 TIRE PRESSURE MONITORING _0327404 TIRE PRESSURE WARNING RECEIVER A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING RECEIVER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning ECU and receiver removal/installation are shown below.

Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Register Transmitter ID

·

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

·

Tire pressure warning function


(Click here)for Registration
(Click here)for Initialization

CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST


PROCEDURE

Hide 1. PRECAUTION (w/ Rear Seat Side Airbag)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 3.REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

Hide 62331A 4.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fixed Seat Type)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 73350C 5.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

Hide 6.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Hide 72693 7.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 62331A 8.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL


Hide 9.REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL


Hide 71940A 10.REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

Hide 73350C 11.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Reclining Seat Type)

Hide 12.REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)

Hide 72693 13.REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)

Hide 72996A 14.REMOVE REAR SEATBACK COVER (for Reclining Seat Type)

Hide 15.REMOVE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)

Hide 62331A 16.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Reclining Seat Type)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL


Hide 17.REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Reclining Seat Type)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL


Hide 62471A 18.REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 897B0A 19.REMOVE TIRE PRESSURE WARNING ECU AND RECEIVER

NOTICE:
·

Do not drop, strike or otherwise subject the tire pressure warning ECU and receiver to impact.

·

If the tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.



a.
B469792

Remove the bolt.


b.

Disengage the 2 guides.


c.

Disconnect the connector to remove the tire pressure warning ECU and receiver.