Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2018.04
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Driver Seat Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driver Seat Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "D-Seat" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "D-Seat" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "D-Seat" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Front Seat ECU RH Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Position control ECU assembly LH branch line or connector (for LHD)

·

Power source circuit of position control ECU assembly LH (for LHD)

·

Position control ECU assembly LH ground circuit (for LHD)

·

Position control ECU assembly LH (for LHD)

·

Position control ECU assembly RH branch line or connector (for RHD)

·

Power source circuit of position control ECU assembly RH (for RHD)

·

Position control ECU assembly RH ground circuit (for RHD)

·

Position control ECU assembly RH (for RHD)



WIRING DIAGRAM

for LHD:
C382027E10
5.24,4.823 5.698,5.021 0.458,0.198 10 false b23 5.24,3.333 5.698,3.531 0.458,0.198 10 false b23 5.25,1.385 5.708,1.583 0.458,0.198 10 false b25 5.24,4.073 5.698,4.271 0.458,0.198 10 false b25 5.271,0.563 5.729,0.76 0.458,0.198 10 false 13 5.271,1.146 5.729,1.344 0.458,0.198 10 false 14 5.667,0.802 6.125,1 0.458,0.198 10 false CANP 5.677,1.396 6.135,1.594 0.458,0.198 10 false CANN 1.76,0.677 2.219,0.875 0.458,0.198 10 false 3 1.729,1.26 2.188,1.458 0.458,0.198 10 false 14 0.208,1.781 0.667,1.979 0.458,0.198 10 false R101 0.604,1.781 2.625,2.24 2.021,0.458 10 false No. 6 Junction Connector 5.677,2.615 6.135,2.813 0.458,0.198 10 false IG 5.667,3.333 6.125,3.531 0.458,0.198 10 false +B 5.667,4.073 6.167,4.313 0.5,0.24 10 false SYSB 5.667,4.833 6.125,5.031 0.458,0.198 10 false GND 5.49,5.865 6.844,6.365 1.354,0.5 10 false Position Control ECU Assembly LH 5.313,4.573 5.771,4.771 0.458,0.198 10 false 2 5.271,3.833 5.729,4.031 0.458,0.198 10 false 15 5.313,3.104 5.771,3.302 0.458,0.198 10 false 3 5.313,2.365 5.771,2.563 0.458,0.198 10 false 1 3.729,2.417 4.813,2.719 1.083,0.302 10 false ECU-IG1 NO. 4 3.823,3.167 5.125,3.438 1.302,0.271 10 false P/SEAT F/L 3.719,3.896 5.031,4.167 1.313,0.271 10 false ECU-DCC NO. 2 2.24,3.302 3.177,3.615 0.938,0.313 10 false from Battery 1.688,2.573 3.25,2.969 1.563,0.396 10 false from IG1-NO. 1 Relay 2.24,4.031 3.177,4.344 0.938,0.313 10 false from Battery 5.25,0.792 5.708,0.99 0.458,0.198 10 false b25 5.24,2.594 5.698,2.792 0.458,0.198 10 false b25

for RHD:
C382027E09
5.24,4.823 5.698,5.021 0.458,0.198 10 false a10 5.24,3.333 5.698,3.531 0.458,0.198 10 false a10 5.25,1.385 5.708,1.583 0.458,0.198 10 false a12 5.24,4.073 5.698,4.271 0.458,0.198 10 false a12 5.271,0.563 5.729,0.76 0.458,0.198 10 false 13 5.271,1.146 5.729,1.344 0.458,0.198 10 false 14 5.667,0.802 6.125,1 0.458,0.198 10 false CANP 5.677,1.396 6.135,1.594 0.458,0.198 10 false CANN 1.76,0.677 2.219,0.875 0.458,0.198 10 false 7 1.729,1.26 2.188,1.458 0.458,0.198 10 false 18 0.208,1.781 0.667,1.979 0.458,0.198 10 false R100 0.604,1.781 2.625,2.24 2.021,0.458 10 false No. 5 Junction Connector 5.677,2.615 6.135,2.813 0.458,0.198 10 false IG 5.667,3.333 6.125,3.531 0.458,0.198 10 false +B 5.667,4.073 6.167,4.313 0.5,0.24 10 false SYSB 5.667,4.833 6.125,5.031 0.458,0.198 10 false GND 5.49,5.865 6.844,6.365 1.354,0.5 10 false Position Control ECU Assembly RH 5.313,4.573 5.771,4.771 0.458,0.198 10 false 2 5.271,3.833 5.729,4.031 0.458,0.198 10 false 15 5.313,3.104 5.771,3.302 0.458,0.198 10 false 3 5.313,2.365 5.771,2.563 0.458,0.198 10 false 1 3.729,2.417 4.813,2.719 1.083,0.302 10 false ECU-IG1 NO. 4 3.823,3.167 5.125,3.438 1.302,0.271 10 false P/SEAT F/R 3.719,3.896 5.031,4.167 1.313,0.271 10 false ECU-DCC NO. 2 2.24,3.302 3.177,3.615 0.938,0.313 10 false from Battery 1.688,2.573 3.25,2.969 1.563,0.396 10 false from IG1-NO. 1 Relay 2.24,4.031 3.177,4.344 0.938,0.313 10 false from Battery 5.25,0.792 5.708,0.99 0.458,0.198 10 false a12 5.24,2.594 5.698,2.792 0.458,0.198 10 false a12

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR OPEN IN CAN BUS LINES (POSITION CONTROL ECU ASSEMBLY LH BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (POSITION CONTROL ECU ASSEMBLY RH BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (POSITION CONTROL ECU ASSEMBLY LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the b25 position control ECU assembly LH connector.


c.
C382025C10
1.49,0.385 1.896,0.625 0.406,0.24 2.656,1.677 2.656,0.844 2.656,0.844 2.49,0.844 true 2.833,1.677 2.833,0.594 2.833,0.594 2.667,0.594 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.583,0.427 1.927,0.646 0.344,0.219 10 false b25 2.042,0.771 2.552,1.021 0.51,0.25 10 false CANP 2.208,0.521 2.719,0.771 0.51,0.25 10 false CANN
*a Front view of wire harness connector
(to Position Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b25-13 (CANP) - b25-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the b23 position control ECU assembly LH connector.


b.
C382026C10
1.521,0.125 1.896,0.396 0.375,0.271 1.552,2.542 1.927,2.813 0.375,0.271 0.875,1.438 0.875,0.604 0.875,0.604 1.042,0.604 true 0.865,1.719 0.865,2.219 0.865,2.219 1.031,2.219 true 2.01,3.365 2.01,2.948 2.01,2.948 2.177,2.948 true 1.49,3.365 1.49,2.948 1.49,2.948 1.323,2.948 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.594,0.188 1.906,0.385 0.313,0.198 10 false b25 1.625,2.594 1.938,2.792 0.313,0.198 10 false b23 2.271,2.865 2.906,3.188 0.635,0.323 10 false +B 0.938,2.875 1.573,3.198 0.635,0.323 10 false GND 1.125,2.135 1.76,2.458 0.635,0.323 10 false SYSB 1.146,0.521 1.781,0.844 0.635,0.323 10 false IG
*a Front view of wire harness connector
(to Position Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b23-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b23-3 (+B) - Body ground Always 11 to 14 V
b25-15 (SYSB) - Body ground Always 11 to 14 V
b25-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (POSITION CONTROL ECU ASSEMBLY RH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the a12 position control ECU assembly RH connector.


c.
C382025C03
1.49,0.385 1.896,0.625 0.406,0.24 2.656,1.677 2.656,0.844 2.656,0.844 2.49,0.844 true 2.833,1.677 2.833,0.594 2.833,0.594 2.667,0.594 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.583,0.427 1.927,0.646 0.344,0.219 10 false a12 2.042,0.771 2.552,1.021 0.51,0.25 10 false CANP 2.208,0.521 2.719,0.771 0.51,0.25 10 false CANN
*a Front view of wire harness connector
(to Position Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-13 (CANP) - a12-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the a10 position control ECU assembly RH connector.


b.
C382026C03
1.521,0.125 1.896,0.396 0.375,0.271 1.552,2.542 1.927,2.813 0.375,0.271 0.875,1.438 0.875,0.604 0.875,0.604 1.042,0.604 true 0.865,1.719 0.865,2.219 0.865,2.219 1.031,2.219 true 2.01,3.365 2.01,2.948 2.01,2.948 2.177,2.948 true 1.49,3.365 1.49,2.948 1.49,2.948 1.323,2.948 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.594,0.188 1.906,0.385 0.313,0.198 10 false a12 1.625,2.594 1.938,2.792 0.313,0.198 10 false a10 2.271,2.865 2.906,3.188 0.635,0.323 10 false +B 0.938,2.875 1.573,3.198 0.635,0.323 10 false GND 1.125,2.135 1.76,2.458 0.635,0.323 10 false SYSB 1.146,0.521 1.781,0.844 0.635,0.323 10 false IG
*a Front view of wire harness connector
(to Position Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a10-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a10-3 (+B) - Body ground Always 11 to 14 V
a12-15 (SYSB) - Body ground Always 11 to 14 V
a12-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)