Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2018.04–2018.08
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 1 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Forward recognition camera

(w/ Toyota Safety Sense)

·

Millimeter wave radar sensor assembly

(w/ Toyota Safety Sense)

·

Blind spot monitor sensor RH

(w/ Blind Spot Monitor System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System or Panoramic View Monitor System)

·

Clearance warning ECU assembly

(w/ TOYOTA Parking Assist-sensor System)

·

Television camera controller

(w/ Panoramic View Monitor System)

·

No. 1 CAN junction connector

·

No. 5 CAN junction connector



WIRING DIAGRAM

C396747E01
0.333,1.031 1.104,1.229 0.771,0.198 10 false 120 Ω 0.938,0.698 1.552,0.896 0.615,0.198 10 false CA1H 1,1.188 1.615,1.385 0.615,0.198 10 false CA1L 1.438,0.698 1.75,0.896 0.313,0.198 10 false 23 1.448,1.188 1.604,1.385 0.156,0.198 10 false 8 3.74,0.719 3.896,0.917 0.156,0.198 10 false 3 3.74,1.177 3.896,1.375 0.156,0.198 10 false 9 4.792,0.719 4.948,0.917 0.156,0.198 10 false 1 4.792,1.177 4.948,1.375 0.156,0.198 10 false 7 5.906,0.708 6.063,0.906 0.156,0.198 10 false 3 5.906,1.177 6.063,1.375 0.156,0.198 10 false 2 6.125,0.802 6.74,1 0.615,0.198 10 false CA2H 6.135,1.271 6.75,1.469 0.615,0.198 10 false CA2L 5.344,1.729 5.802,1.927 0.458,0.198 10 false A30 5.656,1.729 7.063,2.375 1.406,0.646 10 false Millimeter Wave Radar Sensor Assembly* 4.948,5.292 7.135,5.771 2.188,0.479 10 false *: w/ Toyota Safety Sense 3.719,2.948 3.875,3.146 0.156,0.198 10 false 2 3.719,3.417 3.875,3.615 0.156,0.198 10 false 8 2.771,2.958 2.927,3.156 0.156,0.198 10 false 5 2.76,3.427 3.073,3.625 0.313,0.198 10 false 11 2.208,3.031 2.823,3.229 0.615,0.198 10 false CA1P 2.219,3.521 2.833,3.719 0.615,0.198 10 false CA1N 1.521,3.99 1.833,4.188 0.313,0.198 10 false V6 1.75,3.99 3.021,4.823 1.271,0.833 10 false Forward Recognition Camera* 0.042,5.135 0.5,5.333 0.458,0.198 10 false K76 0.354,5.135 2.302,5.802 1.948,0.667 10 false Central Gateway ECU (Network Gateway ECU) 4.792,2.948 4.948,3.146 0.156,0.198 10 false 5 4.771,3.417 5.083,3.615 0.313,0.198 10 false 11 3.469,3.99 3.927,4.188 0.458,0.198 10 false A66 3.792,3.99 5.042,4.708 1.25,0.719 10 false No. 1 CAN Junction Connector

C396748E01
4.76,0.979 4.917,1.177 0.156,0.198 10 false 5 4.729,1.438 5.042,1.635 0.313,0.198 10 false 15 3.677,0.979 3.833,1.177 0.156,0.198 10 false 3 3.615,1.448 3.927,1.646 0.313,0.198 10 false 13 2.719,0.979 2.875,1.177 0.156,0.198 10 false 2 2.719,1.448 2.875,1.646 0.156,0.198 10 false 7 2.188,1.073 2.802,1.271 0.615,0.198 10 false CA1P 2.177,1.563 2.792,1.76 0.615,0.198 10 false CA1N 1.438,1.969 1.75,2.167 0.313,0.198 10 false W5 1.729,1.969 2.896,2.76 1.167,0.792 10 false Blind Spot Monitor Sensor RH*1 0.125,8.167 5.021,8.365 4.896,0.198 10 false *1: w/ Blind Spot Monitor System 4.771,1.875 4.927,2.073 0.156,0.198 10 false 4 4.729,2.344 5.042,2.542 0.313,0.198 10 false 14 5.854,1.885 6.01,2.083 0.156,0.198 10 false 4 5.854,2.354 6.01,2.552 0.156,0.198 10 false 1 6.083,1.99 6.698,2.188 0.615,0.198 10 false CANH 6.094,2.458 6.708,2.656 0.615,0.198 10 false CANL 5.385,2.865 5.698,3.063 0.313,0.198 10 false m3 5.635,2.865 7.094,3.615 1.458,0.75 10 false Rear Television Camera Assembly*2 0.115,8.5 5.615,8.698 5.5,0.198 10 false *2: w/ Parking Assist Monitor System 5.844,3.99 6,4.188 0.156,0.198 10 false 4 5.844,4.458 6,4.656 0.156,0.198 10 false 1 6.094,4.094 6.708,4.292 0.615,0.198 10 false CANH 6.115,4.563 6.729,4.76 0.615,0.198 10 false CANL 5.417,4.99 5.729,5.188 0.313,0.198 10 false m4 5.667,4.99 7.125,5.74 1.458,0.75 10 false Rear Television Camera Assembly*3 2.896,8.188 6.552,8.583 3.656,0.396 10 false *3: w/ Panoramic View Monitor System 1.781,5.198 2.906,6.031 1.125,0.833 10 false Television Camera Controller*3 1.406,5.198 2.021,5.396 0.615,0.198 10 false R123 2.188,4.302 2.802,4.5 0.615,0.198 10 false CANH 2.208,4.792 2.823,4.99 0.615,0.198 10 false CANL 2.698,4.208 3.01,4.406 0.313,0.198 10 false 12 2.708,4.688 3.021,4.885 0.313,0.198 10 false 13 3.667,4.198 3.823,4.396 0.156,0.198 10 false 8 3.635,4.677 3.948,4.875 0.313,0.198 10 false 18 3.656,6.052 3.813,6.25 0.156,0.198 10 false 1 3.625,6.531 3.938,6.729 0.313,0.198 10 false 11 1.448,6.052 1.604,6.25 0.156,0.198 10 false 9 1.417,6.531 1.729,6.729 0.313,0.198 10 false 24 0.917,6.052 1.531,6.25 0.615,0.198 10 false CAXH 0.969,6.542 1.583,6.74 0.615,0.198 10 false CAXL 0.333,6.396 1.104,6.594 0.771,0.198 10 false 120 Ω 0.042,7.125 0.5,7.323 0.458,0.198 10 false K76 0.344,7.125 2.292,7.875 1.948,0.75 10 false Central Gateway ECU (Network Gateway ECU) 3.406,7.021 3.865,7.219 0.458,0.198 10 false R98 3.708,7.021 4.917,7.771 1.208,0.75 10 false No. 5 CAN Junction Connector 4.771,6.063 4.927,6.26 0.156,0.198 10 false 2 4.729,6.531 5.042,6.729 0.313,0.198 10 false 12 5.781,6.063 6.094,6.26 0.313,0.198 10 false 17 5.781,6.542 6.094,6.74 0.313,0.198 10 false 18 6.104,6.167 6.417,6.365 0.313,0.198 10 false R1 6.115,6.625 6.427,6.823 0.313,0.198 10 false R2 5.563,7.063 6.021,7.26 0.458,0.198 10 false R39 5.875,7.052 7.063,7.958 1.188,0.906 10 false Clearance Warning ECU Assembly*4 2.885,8.521 6.354,8.844 3.469,0.323 10 false *4: w/ TOYOTA Parking Assist-sensor System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A66 No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C376602C27
0.146,1.313 0.563,1.573 0.417,0.26 3.615,1.219 4.031,1.479 0.417,0.26 1.01,1.344 1.01,0.76 1.01,0.76 0.844,0.76 true 1.365,1.344 1.365,0.521 1.365,0.521 1.198,0.521 true 1.719,1.344 1.719,0.25 1.719,0.25 1.552,0.25 true 2.427,1.344 2.427,0.521 2.427,0.521 2.594,0.521 true 1.01,1.625 1.01,2.063 1.01,2.063 0.844,2.063 true 1.365,1.635 1.365,2.302 1.365,2.302 1.198,2.302 true 1.719,1.625 1.719,2.521 1.719,2.521 1.552,2.521 true 2.417,1.625 2.417,2.292 2.417,2.292 2.583,2.292 true 5.302,1.073 5.302,0.635 5.302,0.635 5.135,0.635 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 3.885,0.115 4.198,0.313 0.313,0.198 10 false *1 0.24,1.365 0.615,1.615 0.375,0.25 10 false A66 3.719,1.271 4.094,1.521 0.375,0.25 10 false K68 0.271,0.698 0.865,0.969 0.594,0.271 10 false CANH*b 0.625,0.448 1.219,0.719 0.594,0.271 10 false CANH*c 0.979,0.177 1.573,0.448 0.594,0.271 10 false CANH*d 2.688,0.448 3.281,0.719 0.594,0.271 10 false CANH*e 0.271,1.99 0.865,2.26 0.594,0.271 10 false CANL*b 0.635,2.229 1.229,2.5 0.594,0.271 10 false CANL*c 1,2.448 1.594,2.719 0.594,0.271 10 false CANL*d 2.667,2.219 3.26,2.49 0.594,0.271 10 false CANL*e 4.865,0.563 5.302,0.813 0.438,0.25 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Central Gateway ECU (Network Gateway ECU)
*e to No. 5 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A66-1 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*
A66-7 (CANL) - K68-4 (CG)
A66-2 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera*
A66-8 (CANL) - K68-4 (CG)
A66-3 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
A66-9 (CANL) - K68-4 (CG)
A66-5 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 5 CAN junction connector
A66-11 (CANL) - K68-4 (CG)


*: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 5 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C376602C04
0.167,1.313 0.583,1.573 0.417,0.26 3.615,1.219 4.031,1.479 0.417,0.26 1.708,1.344 1.708,0.552 1.708,0.552 1.542,0.552 true 1.719,1.615 1.719,2.281 1.719,2.281 1.552,2.281 true 5.135,0.583 5.302,0.583 5.302,0.583 5.302,1.083 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 3.885,0.115 4.198,0.313 0.313,0.198 10 false *1 0.26,1.365 0.635,1.615 0.375,0.25 10 false A66 3.719,1.271 4.094,1.521 0.375,0.25 10 false K68 0.969,0.49 1.563,0.76 0.594,0.271 10 false CANH*b 0.99,2.208 1.583,2.479 0.594,0.271 10 false CANL*b 4.854,0.521 5.292,0.771 0.438,0.25 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
A66-3 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A66-9 (CANL) - K68-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the R98 No. 5 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C351272C92
0.125,1.313 0.552,1.563 0.427,0.25 3.677,1.333 4.104,1.583 0.427,0.25 0.865,1.365 0.865,0.865 0.865,0.865 0.698,0.865 true 0.688,2.01 0.854,2.01 0.854,2.01 0.854,1.594 true 4.958,0.688 5.125,0.688 5.125,0.688 5.125,1.104 true 0.938,2.26 1.104,2.26 1.104,2.26 1.104,1.594 true 1.115,1.385 1.115,0.635 1.115,0.635 0.948,0.635 true 1.604,1.385 1.604,0.406 1.604,0.406 1.771,0.406 true 1.854,1.375 1.854,0.615 1.854,0.615 2.021,0.615 true 1.771,2.479 1.604,2.479 1.604,2.479 1.604,1.604 true 2.021,2.24 1.854,2.24 1.854,2.24 1.854,1.615 true 1.365,1.385 1.365,0.406 1.365,0.406 1.198,0.406 true 1.188,2.479 1.354,2.479 1.354,2.479 1.354,1.604 true 2.604,1.375 2.604,0.875 2.604,0.875 2.781,0.875 true 2.802,2.01 2.604,2.01 2.604,2.01 2.604,1.594 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.198,1.354 0.552,1.573 0.354,0.219 10 false R98 0.115,0.781 0.844,1 0.729,0.219 10 false CANH*b 0.365,0.552 1.094,0.771 0.729,0.219 10 false CANH*c 0.615,0.333 1.344,0.552 0.729,0.219 10 false CANH*d 0.115,1.938 0.844,2.156 0.729,0.219 10 false CANL*b 0.365,2.177 1.094,2.396 0.729,0.219 10 false CANL*c 0.615,2.417 1.344,2.635 0.729,0.219 10 false CANL*d 4.688,0.615 5.417,0.833 0.729,0.219 10 false CG 3.823,0.521 4.552,0.74 0.729,0.219 10 false *1 3.771,1.365 4.125,1.583 0.354,0.219 10 false K68 1.865,0.323 2.594,0.542 0.729,0.219 10 false CANH*e 1.865,2.406 2.594,2.625 0.729,0.219 10 false CANL*e 2.125,0.531 2.854,0.75 0.729,0.219 10 false CANH*f 2.125,2.167 2.854,2.385 0.729,0.219 10 false CANL*f 2.833,0.781 3.563,1 0.729,0.219 10 false CANH*g 2.854,1.906 3.583,2.125 0.729,0.219 10 false CANL*g
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*d to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*e to Rear Television Camera Assembly
(w/ Parking Assist Monitor System or Panoramic View Monitor System)
*f to No. 1 CAN Junction Connector
*g to Television Camera Controller
(w/ Panoramic View Monitor System)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R98-1 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
R98-11 (CANL) - K68-4 (CG)
R98-2 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*1
R98-12 (CANL) - K68-4 (CG)
R98-3 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor RH*2
R98-13 (CANL) - K68-4 (CG)
R98-4 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera assembly*3
R98-14 (CANL) - K68-4 (CG)
R98-5 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
R98-15 (CANL) - K68-4 (CG)
R98-8 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Television camera controller*4
R98-18 (CANL) - K68-4 (CG)


·

*1: w/ TOYOTA Parking Assist-sensor System

·

*2: w/ Blind Spot Monitor System

·

*3: w/ Parking Assist Monitor System or Panoramic View Monitor System

·

*4: w/ Panoramic View Monitor System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C351272C51
0.125,1.313 0.552,1.563 0.427,0.25 3.677,1.333 4.104,1.583 0.427,0.25 0.865,1.365 0.865,0.865 0.865,0.865 0.698,0.865 true 0.688,2.01 0.854,2.01 0.854,2.01 0.854,1.594 true 4.958,0.615 5.125,0.615 5.125,0.615 5.125,1.115 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.188,1.354 0.542,1.573 0.354,0.219 10 false R98 0.156,0.781 0.885,1 0.729,0.219 10 false CANH*b 0.146,1.938 0.875,2.156 0.729,0.219 10 false CANL*b 4.688,0.531 5.417,0.75 0.729,0.219 10 false CG 3.823,0.521 4.552,0.74 0.729,0.219 10 false *1 3.771,1.375 4.125,1.594 0.354,0.219 10 false K68
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
R98-1 (CANH) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R98-11 (CANL) - K68-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351275C12
1.594,0.198 2.01,0.469 0.417,0.271 4.938,0.292 5.354,0.563 0.417,0.271 1.313,1.24 1.313,0.635 1.313,0.635 1.177,0.635 true 1.115,2.083 1.25,2.083 1.25,2.083 1.25,1.385 true 4.958,0.719 5.125,0.719 5.125,0.719 5.125,1.104 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.688,0.25 2,0.448 0.313,0.198 10 false K76 0.781,0.573 1.333,0.771 0.552,0.198 10 false CA1L 4.719,0.635 5.271,0.833 0.552,0.198 10 false CG 0.698,2.01 1.25,2.208 0.552,0.198 10 false CA1H 5.021,0.344 5.333,0.542 0.313,0.198 10 false K68 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K76-23 (CA1H) - K68-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
K76-8 (CA1L) - K68-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR