When the position control ECU assembly (driver seat) does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2650 | Slide Sensor Malfunction | Slide motor position sensor signal not received when power seat moved forward or backward | ·
Position control ECU assembly (driver seat) ·
Slide motor (Upper seat track rail sub-assembly (driver seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2650 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Slide Operation |
Slide motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b19*1 or a5*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b19-2 - b19-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a5-2 - a5-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Component with harness connected
(Slide Motor (Front Seat Adjuster Assembly (Driver Seat)) |
Reconnect the b19*1 or a5*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b19-2 - Body ground | Slide motor operating | 4.5 to 4.8 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a5-2 - Body ground | Slide motor operating | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b25*1 or a12*2 position control ECU assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-26 (SSRS) - b19-2 | Always | Below 1 Ω |
| b25-26 (SSRS) or b19-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - b19-3 | Always | Below 1 Ω |
| b25-12 (SENG) or b19-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-26 (SSRS) - a5-2 | Always | Below 1 Ω |
| a12-26 (SSRS) or a5-2 - Body ground | Always | 10 kΩ or higher |
| a12-12 (SENG) - a5-3 | Always | Below 1 Ω |
| a12-12 (SENG) or a5-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the slide motor (front seat adjuster assembly (driver seat)).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Inspect the slide motor (front seat adjuster assembly (driver seat)).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b23*1 or a10*2 position control ECU assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b23-1 (SLD+) - b19-4 | Always | Below 1 Ω |
| b23-1 (SLD+) or b19-4 - Body ground | Always | 10 kΩ or higher |
| b23-5 (SLD-) - b19-1 | Always | Below 1 Ω |
| b23-5 (SLD-) or b19-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a10-1 (SLD+) - a5-4 | Always | Below 1 Ω |
| a10-1 (SLD+) or a5-4 - Body ground | Always | 10 kΩ or higher |
| a10-5 (SLD-) - a5-1 | Always | Below 1 Ω |
| a10-5 (SLD-) or a5-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG