This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. | ·
Position control ECU assembly (driver seat) ·
Slide motor (Upper seat track rail sub-assembly (driver seat)) ·
Power Seat Tilt Motor Assembly (Driver Seat) ·
Power Seat Lifter Motor Assembly (Driver Seat) ·
Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the b25*1 or a12*2 position control ECU assembly (driver seat) connector.
Disconnect the b19*1 or a5*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-26 (SSRS) - b19-2 | Always | Below 1 Ω |
| b25-26 (SSRS) or b19-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - b19-3 | Always | Below 1 Ω |
| b25-12 (SENG) or b19-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-26 (SSRS) - a5-2 | Always | Below 1 Ω |
| a12-26 (SSRS) or a5-2 - Body ground | Always | 10 kΩ or higher |
| a12-12 (SENG) - a5-3 | Always | Below 1 Ω |
| a12-12 (SENG) or a5-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b19*1 or a5*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b19-2 - b19-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a5-2 - a5-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b25*1 or a12*2 position control ECU assembly (driver seat) connector.
Disconnect the b20*1 or a6*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-10 (SSFV) - b20-2 | Always | Below 1 Ω |
| b25-10 (SSFV) or b20-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - b20-3 | Always | Below 1 Ω |
| b25-12 (SENG) or b20-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-10 (SSFV) - a6-2 | Always | Below 1 Ω |
| a12-10 (SSFV) or a6-2 - Body ground | Always | 10 kΩ or higher |
| a12-12 (SENG) - a6-3 | Always | Below 1 Ω |
| a12-12 (SENG) or a6-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b20*1 or a6*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b20-2 - b20-3 | Front vertical switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a6-2 - a6-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b25*1 or a12*2 position control ECU assembly (driver seat) connector.
Disconnect the b21*1 or a7*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-25 (SSRL) - b21-2 | Always | Below 1 Ω |
| b25-25 (SSRL) or b21-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - b21-3 | Always | Below 1 Ω |
| b25-12 (SENG) or b21-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-25 (SSRL) - a7-2 | Always | Below 1 Ω |
| a12-25 (SSRL) or a7-2 - Body ground | Always | 10 kΩ or higher |
| a12-12 (SENG) - a7-3 | Always | Below 1 Ω |
| a12-12 (SENG) or a7-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b21*1 or a7*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b21-2 - b21-3 | Lifter switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a7-2 - a7-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b25*1 or a12*2 position control ECU assembly (driver seat) connector.
Disconnect the c1*1 or o1*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-11 (SSRR) - c1-2 | Always | Below 1 Ω |
| b25-11 (SSRR) or c1-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - c1-3 | Always | Below 1 Ω |
| b25-12 (SENG) or c1-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a12-11 (SSRR) - o1-2 | Always | Below 1 Ω |
| a12-11 (SSRR) or o1-2 - Body ground | Always | 10 kΩ or higher |
| a12-12 (SENG) - o1-3 | Always | Below 1 Ω |
| a12-12 (SENG) or o1-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the c1*1 or o1*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c1-2 - c1-3 | Reclining switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| o1-2 - o1-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat tilt motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat lifter motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the slide motor (upper seat track rail sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT TRACK RAIL ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the reclining motor (front seatback frame sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG