Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM D

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


CAUTION:
·
C328184

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328186

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328185

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform this test with the ATF (Automatic transaxle Fluid) at the normal operating temperature: 50 to 80°C (122 to 176°F)

·

Be careful to prevent the SST hose from contacting the exhaust pipe.

·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the air conditioning off.

·

Do not perform the stall test for longer than 5 seconds.

·

When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.

·

Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.



a.

Measure the line pressure.

i.

Warm up the ATF.


ii.

Lift the vehicle.


iii.

Remove the engine under cover.


iv.
C370670N01
0.896,4.01 1.229,4.208 true 2.635,4.115 3.094,4.313 0.458,0.198 10 false SST 1.281,4.146 1.74,4.344 0.458,0.198 10 false SST

Remove the test plug on the front left side of the transaxle case and install SST.

SST
09993-19015  (09993-00010, 09993-00040)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock all 4 wheels.

HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



vii.

Connect the GTS to the DLC3.


viii.

Start the engine.


ix.

Enter the following menus: Powertrain / Transmission / Active Test / Control the Shift Position.

Powertrain > Transmission > Active Test
Tester Display
Control the Shift Position
50004 373 42009

x.

Move the shift lever to D, and then use the GTS to perform the Active Test and hold 3rd gear. Measure the line pressure with the engine idling.

Specified Line Pressure:
Condition D Position
Idling 360 to 430 kPa
(3.6 to 4.4 kgf/cm2, 52 to 63 psi)



xi.

Turn the engine switch off.


xii.
C370672

Disconnect the connector from the wiring harness connector.

HINT:

Disconnect the connector only when performing the D position stall test.



xiii.

Start the engine.


xiv.

Firmly depress the brake pedal with your left foot, move the shift lever to D, depress the accelerator pedal as much as possible with your right foot, and quickly read the line pressure when the engine reaches the stall speed.

Specified Line Pressure:
Condition D Position
Stall test 700 to 1100 kPa
(7.1 to 11.3 kgf/cm2, 101 to 160 psi)



xv.

Turn the engine switch off.


xvi.

Connect the connector to the wiring harness connector.


xvii.

Firmly depress the brake pedal with your left foot, move the shift lever to R, and check the line pressure while the engine is idling and then depress the accelerator pedal as much as possible with your right foot and quickly read the line pressure when the engine reaches the stall speed.

Specified Line Pressure:
Condition R Position
Idling 670 to 820 kPa
(6.8 to 8.4 kgf/cm2, 97 to 119 psi)
Stall test 1600 to 2000 kPa
(16.3 to 20.4 kgf/cm2, 232 to 291 psi)



xviii.

Remove SST and install the test plug.


xix.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
Evaluation
Test Result Possible Cause
Measured values are higher than the specified value in all positions
·

Solenoid (SLT) valve malfunction

·

Regulator valve malfunction


Measured values are lower than the specified value in all positions
·

Solenoid (SLT) valve malfunction

·

Regulator valve malfunction

·

Oil pump malfunction


Pressure is low in D only
·

D position circuit fluid leak

·

No. 1 clutch (C1) malfunction


Pressure is low in R only
·

R position circuit fluid leak

·

No. 2 brake (B2) malfunction

·

No. 3 brake (B3) malfunction