Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM D

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  INITIALIZATION  


RESET TRANSAXLE COMPENSATION CODE


NOTICE:
·

If the following parts have been replaced, initialize the ECM, perform Reset Memory and Perform Road Test to Allow ECM to Learn.

-

Transmission valve body assembly

-

Solenoid (SL3) valve

-

Solenoid (SL4) valve

-

ECM


·

The transaxle compensation code can only be initialized with the GTS.



HINT:

The ECM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, if the automatic transaxle assembly, transmission valve body assembly, solenoid (SL3) valve, solenoid (SL4) valve or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information. The reset procedure is as follows:


a.

Make sure the shift lever is in P or N.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Utility / A/T Code Reset.

Powertrain > Transmission > Utility
Tester Display
A/T Code Reset
50005 373 209

f.

Press "Next" again to proceed.

NOTICE:

After the transaxle compensation code is initialized, perform Reset Memory and Perform Road Test to Allow ECM to Learn.



g.

Press "Exit".



RESET MEMORY


NOTICE:

Reset Memory can be performed only with the GTS.


HINT:

The ECM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, if the automatic transaxle assembly, transmission valve body assembly, solenoid (SL3) valve, solenoid (SL4) valve or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information. The reset procedure is as follows:


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Utility / Reset Memory.

Powertrain > Transmission > Utility
Tester Display
Reset Memory
50005 373 8001

e.

Press "Next".

NOTICE:

After performing Reset Memory, be sure to perform Perform Road Test to Allow ECM to Learn.




PERFORM ROAD TEST TO ALLOW ECM TO LEARN


CAUTION:

Perform the following procedure while strictly observing all traffic laws and speed limits.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / Throttle Sensor Position.

Powertrain > Engine > Data List
Tester Display
Throttle Sensor Position
50003 372 308

g.

From a standstill, achieve highest possible speed with the accelerator pedal opened 15% or less. Keep the accelerator pedal opening angle steady while driving the vehicle.

HINT:

Throttle Sensor Position: 15% or less



h.

Repeat the previous step until shift shock no longer occurs.


i.

From a standstill, achieve highest possible speed with the accelerator pedal opened 25% to 35%. Keep the accelerator pedal opening angle steady while driving the vehicle.

HINT:

Throttle Sensor Position: 25 to 35%



j.

Repeat the previous step until shift shock no longer occurs.