Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open When the engine switch is on (IG) and the battery voltage is 8 V or more, the NSW, P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic).
·

Wire harness or connector

·

Open in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

ECM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure When the engine switch is on (IG) and the battery voltage is 8 V or more, 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic).
·

NSW, P or N input signal

·

R input signal

·

D input signal


·

Wire harness or connector

·

Short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

ECM


Comes on DTC stored SAE Code:
P0705

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnostic Condition Engine switch is on (IG) ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○
Malfunction Condition NSW input signal is ON ○ ○ - -
P input signal is ON - - ○ ○
R input signal is ON - ○ - ○
N input signal is ON - - - -
D input signal is ON ○ - ○ -
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnostic Condition Engine switch is on (IG) ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○
Malfunction Condition NSW input signal is ON - - -
P input signal is ON - - -
R input signal is ON - ○ ○
N input signal is ON ○ ○ -
D input signal is ON ○ - ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

DTC P070562 is stored when any of the above detection patterns are met.


MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R or D). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each with the engine switch on (IG).

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: P070513 or P070562.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C346756E06
0.906,0.938 2.594,1.135 1.688,0.198 10 false to ST Relay 0.365,1.698 2.969,1.896 2.604,0.198 10 false from ECU-ACC Fuse 0.375,2.51 1.667,3.229 1.292,0.719 10 false from BKUP LP Fuse 2.042,3.833 2.5,4.031 0.458,0.198 10 false C55 2.031,3.979 4.583,4.198 2.552,0.219 10 false Park/Neutral Position Switch Assembly 5.74,4.094 6.177,4.292 0.438,0.198 10 false ECM 5.323,0.844 5.76,1.042 0.438,0.198 10 false NSW 5.323,3.26 5.76,3.458 0.438,0.198 10 false D 5.323,2.656 5.76,2.854 0.438,0.198 10 false N 5.323,2.063 5.76,2.26 0.438,0.198 10 false R 5.333,1.458 5.771,1.656 0.438,0.198 10 false P 3.781,1.458 4.219,1.656 0.438,0.198 10 false 3 3.781,2.063 4.219,2.26 0.438,0.198 10 false 2 3.781,2.656 4.219,2.854 0.438,0.198 10 false 8 3.781,3.26 4.219,3.458 0.438,0.198 10 false 7 3.771,0.854 4.208,1.052 0.438,0.198 10 false 4 3.552,0.854 3.99,1.052 0.438,0.198 10 false B 3.479,3.25 3.917,3.448 0.438,0.198 10 false DL 3.479,2.656 3.917,2.854 0.438,0.198 10 false NL 3.479,2.063 3.917,2.26 0.438,0.198 10 false RL 3.479,1.458 3.917,1.656 0.438,0.198 10 false PL 2.771,2.365 3.208,2.563 0.438,0.198 10 false RB 2.583,2.365 3.021,2.563 0.438,0.198 10 false 1 2.573,0.865 3.01,1.063 0.438,0.198 10 false 9 2.781,0.865 3.219,1.063 0.438,0.198 10 false L 4.969,0.969 5.406,1.167 0.438,0.198 10 false A78 4.969,1.573 5.406,1.771 0.438,0.198 10 false C58 5.01,0.771 5.448,0.969 0.438,0.198 10 false 57 5.01,3.177 5.448,3.375 0.438,0.198 10 false 34 5,2.573 5.438,2.771 0.438,0.198 10 false 65 5.021,1.969 5.458,2.167 0.438,0.198 10 false 35 5.021,1.375 5.458,1.573 0.438,0.198 10 false 64 4.969,2.177 5.406,2.375 0.438,0.198 10 false C58 4.969,2.771 5.406,2.969 0.438,0.198 10 false C58 4.979,3.375 5.417,3.573 0.438,0.198 10 false C58 5.99,0.677 6.427,0.875 0.438,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION



HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch assembly status ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Neutral Position SW
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 20,15,14,13,28


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the C55 park/neutral position switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C55-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
a.

Disconnect the C55 park/neutral position switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C55-4 (B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C275091C06
1.167,1.708 0.74,1.177 true 1.344,1.708 1.125,1.188 true 1.604,1.688 1.75,1.167 true 1.896,1.698 2.177,1.177 true 1.75,2.135 2.052,2.625 true 1.417,2.135 1.5,2.646 true 1.24,2.146 1.042,2.646 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.01,2.667 1.167,2.865 0.156,0.198 10 false L 1.438,2.667 1.75,2.865 0.313,0.198 10 false NL 2,2.667 2.313,2.865 0.313,0.198 10 false DL 0.667,0.969 0.823,1.167 0.156,0.198 10 false B 1.021,0.969 1.333,1.167 0.313,0.198 10 false PL 1.667,0.969 1.979,1.167 0.313,0.198 10 false RL 2.104,0.969 2.417,1.167 0.313,0.198 10 false RB
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the C55 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
Shift lever not in D, S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Connect the C55 park/neutral position switch assembly connector.


b.

Disconnect the C58 ECM connector.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C58-64 (P) - Body ground Shift lever in P 11 to 14 V
Shift lever not in P Below 1 V
C58-35 (R) - Body ground Shift lever in R 11 to 14 V*
Shift lever not in R Below 1 V
C58-65 (N) - Body ground Shift lever in N 11 to 14 V
Shift lever not in N Below 1 V
C58-34 (D) - Body ground Shift lever in D, S, "+" or "-" 11 to 14 V
Shift lever not in D, S, "+" or "-" Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back-up lights.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Turn the engine switch off.


b.

Disconnect the A78 ECM connector.


c.

Disconnect the C55 park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-4 (B) - A78-57 (NSW) Always Below 1 Ω
C55-4 (B) or A78-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR