Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P071015  Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The Automatic Transaxle Fluid (ATF) temperature sensor converts the automatic transaxle fluid temperature into a resistance value for use by the ECM.

C146747E10
3.708,1.75 4.021,1.25 4.021,1.25 4.083,1.25 false 4.125,1.146 5.51,1.448 1.385,0.302 10 false Acceptable Range 4.281,2.969 5.177,3.188 0.896,0.219 10 false Temperature 1.531,0.625 2.313,0.844 0.781,0.219 10 false Resistance

The ECM applies voltage to the ATF temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature rises, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature rises.

The ECM calculates the ATF temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open The ATF temperature sensor voltage is more than 4.915 V for 0.5 seconds when either of the following conditions is met (1-trip detection logic):
·

900 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were -29.375°C (-20.875°F) or less at engine start).

·

10 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were higher than -29.375°C (-20.875°F) at engine start).


·

Wiring harness connector

·

Open in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

ECM


Comes on DTC stored SAE Code:
P0713

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 900 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were -29.375°C (-20.875°F) or less at engine start). ○ -
10 seconds or more have elapsed since engine start (engine coolant temperature and intake air temperature were higher than -29.375°C (-20.875°F) at engine start). - ○
Malfunction Condition ATF temperature sensor voltage is more than 4.915 V ○ ○
Duration 0.5 seconds or more 0.5 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

HINT:

This DTC is stored when either of the above detection patterns are met.


MONITOR DESCRIPTION

This DTC indicates an open in the ATF temperature sensor circuit. The ATF temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect an open in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is more than 156 kΩ*, the ECM interprets this as a malfunction of the ATF temperature sensor or wiring and will illuminate the MIL and store this DTC.

*: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked on the GTS display.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Wait for 15 minutes or more with the engine running.

8.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

9.

Input the DTC: P071015.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 80°C (176°F): After stall speed test

·

Equal to ambient temperature: When engine is cold


If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted.
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
HINT:
·

If DTC P071015 is output and the GTS indicates -40°C (-40°F), the circuit is open.

Measure the resistance between terminal THO1 (OIL) and body ground.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

·

If the circuit related to the ATF temperature sensor becomes open, DTC P071015 is stored immediately (in 0.5 seconds). When DTC P071015 is stored, DTC P071000 cannot be detected.

It is not necessary to inspect the circuit when DTC P071000 is stored.





PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR CIRCUIT)
a.

Disconnect the C58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-84 (THO1) - C58-83 (ETHO) Always 79 Ω to 156 kΩ
C58-84 (THO1) - Other terminals Always 10 kΩ or higher
C58-83 (ETHO) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the C54 wiring harness connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-84 (THO1) - C54-13 (OIL) Always Below 1 Ω
C58-83 (ETHO) - C54-12 (E2) Always Below 1 Ω
C58-84 (THO1) or C54-13 (OIL) - Other terminals Always 10 kΩ or higher
C58-83 (ETHO) or C54-12 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
a.
C370674C01
0.417,1 0.833,1.25 0.417,0.25 1.625,1.917 1.875,1.5 true 2.292,1.917 2.042,1.5 true 0.573,1.031 0.729,1.229 0.156,0.198 10 false A 1.229,1.844 1.844,2.042 0.615,0.198 10 false THO1 2.354,1.854 2.969,2.052 0.615,0.198 10 false E2 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector from the automatic transaxle assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-17 (E2) - A-18 (THO1) Always 79 Ω to 156 kΩ
A-17 (E2) - Other terminals Always 10 kΩ or higher
A-18 (THO1) - Other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the drivability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)