Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351195 AUTOMATIC TRANSAXLE UNIT A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35104V 1.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C296954

Using a screwdriver with its tip wrapped with protective tape, remove the transmission breather hose sub-assembly from the transaxle case sub-assembly.


b.
C134952C01
2.927,2.396 2.927,2.677 false 2,2.521 2.438,2.521 false 1.635,1.698 1.99,1.698 false 0.635,0.875 0.792,0.604 0.792,0.604 0.927,0.604 false 1.469,1.625 1.635,1.781 0.167,0.156 10 *2 0.958,0.531 1.135,0.688 0.177,0.156 10 *1 1.844,2.448 2,2.604 0.156,0.156 10 *3 2.875,2.688 3.042,2.854 0.167,0.167 10 *4
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 No. 2 Breather Plug
*4 O-ring


Using a screwdriver with its tip wrapped with protective tape, remove the No. 1 breather plug from the breather plug hose.


c.

Using a screwdriver with its tip wrapped with protective tape, remove the No. 2 breather plug from the breather plug hose.


d.

Using a screwdriver with its tip wrapped with protective tape, remove the O-ring from the No. 2 breather plug.


Hide 35572A 2.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C136685

Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.


Hide 84540 3.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136686

Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 32901C 4.REMOVE OIL COOLER UNION SUB-ASSEMBLY

a.
C395091C01
0.333,0.427 0.333,0.26 0.333,0.26 0.698,0.26 false 0.583,0.427 0.583,0.26 false 0.854,1.583 1.073,1.76 0.219,0.177 10 true *1 0.719,0.146 0.938,0.323 0.219,0.177 10 true *2
*1 Union Bolt
*2 Gasket


Remove the union bolt and 2 gaskets from the transaxle case sub-assembly.


b.

Remove the bolt and oil cooler union sub-assembly from the transaxle case sub-assembly.


Hide 32921U 5.REMOVE OIL COOLER INLET ELBOW

a.
C395092

Remove the oil cooler inlet elbow from the transaxle case sub-assembly.


b.

Remove the O-ring from the oil cooler inlet elbow.


Hide 35104Q 6.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C390871

Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.


Hide 35104R 7.REMOVE NO. 2 TRANSAXLE CASE PLUG

a.
C317145

Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.


b.

Remove the 3 gaskets from the 3 No. 2 transaxle case plugs.


Hide 8.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C385282C01
0.594,1.458 0.75,1.458 0.75,1.458 1.01,1.844 false 2.927,1.552 2.771,1.552 2.771,1.552 2.448,1.802 false 0.427,1.375 0.698,1.635 0.271,0.26 10 false *a 2.969,1.448 3.24,1.708 0.271,0.26 10 false *a
*a Wooden Block


Support the automatic transaxle assembly with wooden blocks.


Hide 35106A 9.REMOVE OVERFLOW PLUG

a.
C317147

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


Hide 35125C 10.REMOVE NO. 1 TRANSMISSION OIL FILLER TUBE

a.
C317148

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


Hide 35106D 11.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C385275

Remove the 19 bolts and automatic transaxle oil pan sub-assembly from the transaxle case sub-assembly.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all of the bolts and carefully remove the automatic transaxle oil pan sub-assembly.



Hide 35168A 12.REMOVE AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Remove the automatic transaxle oil pan gasket from the automatic transaxle oil pan sub-assembly.


Hide 35394 13.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C317150C01
1.948,0.531 1.948,0.167 1.948,0.167 0.302,0.167 false 0.885,1.052 0.885,0.177 false 1.594,0.656 1.594,0.167 false 1.115,1.49 1.115,0.177 false 0.104,0.104 0.458,0.385 0.354,0.281 10 false *1
*1 Transmission Oil Cleaner Magnet


Remove the 4 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 35394 14.INSPECT TRANSMISSION OIL CLEANER MAGNET

Hide 35330 15.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C379911

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C317151C02
0.719,0.406 1.26,0.406 false 0.531,0.333 0.896,0.677 0.365,0.344 10 false *1
*1 O-ring


Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 16.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C379912

Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.



Hide 35145C 17.REMOVE TRANSAXLE CASE GASKET

a.
C201316

Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.


Hide 35015S 19.REMOVE REFILL PLUG

a.
C379913

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


Hide 35102B 20.REMOVE REAR TRANSAXLE COVER PLUG

a.
C379914

Remove the 3 rear transaxle cover plugs from the rear transaxle cover sub-assembly.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the 3 rear transaxle cover plugs.


Hide 35102 21.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C379915

Remove the 14 bolts from the rear transaxle cover sub-assembly.


b.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.


c.
C274807

Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the transaxle case sub-assembly.


d.
C297890C06
1.063,1.292 0.74,0.521 0.74,0.521 0.604,0.521 false 0.729,1.542 0.542,1.115 0.542,1.115 0.406,1.115 false 0.438,0.417 0.771,0.688 0.333,0.271 10 false *1 0.219,1.01 0.5,1.375 0.281,0.365 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Bearing Race


Remove the thrust needle roller bearing and thrust bearing race from the rear transaxle cover sub-assembly.


e.
C299131C04
1.365,0.5 1.469,0.5 1.469,0.5 1.719,0.823 true 1.958,1.302 2.219,1.823 2.219,1.823 2.083,1.823 true 1.188,0.417 1.51,0.688 0.323,0.271 10 false *1 1.906,1.719 2.229,1.99 0.323,0.271 10 false *1
*1 Oil Seal Ring


Using a screwdriver with its tip wrapped with protective tape, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.


f.
C201318

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


g.
C194888C10
0.792,2.385 1.01,2.385 1.01,2.385 1.51,0.906 true 0.49,2.281 0.802,2.458 0.313,0.177 10 false SST 3.031,0.427 3.208,0.604 0.177,0.177 10 false *a 0.323,0.844 0.5,1.021 0.177,0.177 10 false *b
*a Turn
*b Hold


Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

SST
09319-60020  


Hide 35650 22.REMOVE REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C202901C10
0.604,1.281 0.365,1.552 0.365,1.552 0.365,2.094 false 2.281,0.219 2.021,0.219 2.021,0.219 2.146,1.375 false 2.323,0.115 2.5,0.281 0.177,0.167 10 false *1 0.313,2.115 0.49,2.271 0.177,0.156 10 false *2
*1 Thrust Needle Roller Bearing
*2 Rear Multiple Disc Clutch Assembly


Remove the rear multiple disc clutch assembly from the transaxle case sub-assembly.


b.

Remove the thrust needle roller bearing from the transaxle case sub-assembly.


c.
C224456C01
1.771,0.229 1.948,0.229 false 1.625,1.917 1.458,1.917 false 1.979,0.156 2.167,0.323 0.188,0.167 10 *1 1.302,1.844 1.49,2.01 0.188,0.167 10 *2
*1 O-ring
*2 Oil Seal Ring


Using a screwdriver with its tip wrapped with protective tape, remove the O-ring from the rear multiple disc clutch assembly.


d.

Using a screwdriver with its tip wrapped with protective tape, remove the oil seal ring from the rear multiple disc clutch assembly.


Hide 35730 23.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C317752C01
2.083,0.573 2.302,0.177 2.302,0.177 2.458,0.177 true 2.615,1.615 2.948,1.552 2.948,1.552 2.417,1.354 true 2.51,0.094 2.844,0.385 0.333,0.292 10 false *1 2.99,1.448 3.198,1.656 0.208,0.208 10 true *a
*1 Snap Ring
*a Protective Tape


Using 2 screwdrivers with their tips wrapped with protective tape and a hammer, remove the snap ring from the rear multiple disc clutch assembly.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C201321C01
1.302,0.292 0.531,0.406 0.531,0.406 0.531,0.469 false 0.49,0.479 0.667,0.667 0.177,0.188 10 *1
*1 Rear Planetary Sun Gear Assembly


Remove the rear planetary sun gear assembly from the rear multiple disc clutch assembly.


c.
C201526C01
2.125,0.885 2.24,1 2.24,1 2.24,1.323 false 1.375,0.125 1.719,0.125 1.719,0.125 1.875,0.208 false 1.219,0.052 1.396,0.208 0.177,0.156 10 false *1 2.188,1.333 2.365,1.51 0.177,0.177 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Bearing Race


Remove the thrust needle roller bearing and thrust bearing race from the rear multiple disc clutch assembly.


Hide 35111C 25.REMOVE TRANSAXLE HOUSING

a.
C205232

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.


Hide 26.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE)

a.
C201323N05
2.527,0.393 2.858,0.535 0.332,0.141 10 SST 2.492,0.475 2.117,0.475 false

Using SST, remove the differential drive pinion tapered roller bearing RH (outer race) and shim from the transaxle housing.

SST
09308-00010  


Hide 43410M 27.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C201325N06
1.802,0.656 2.833,0.417 2.833,0.417 1.875,1.188 false 2.885,0.323 3.313,0.563 0.427,0.24 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09950-60011  (09951-00550)
09950-70010  (09951-07200)


Hide 28.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C201324N07
2.834,0.246 3.125,0.408 0.291,0.163 10 SST 2.816,0.329 2.701,0.329 2.701,0.329 2.357,0.568 false

Using SST, remove the front differential case front tapered roller bearing (outer race) and shim from the transaxle housing.

SST
09308-00010  


Hide 35882A 29.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C201326

Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.


Hide 35174 30.REMOVE TRANSAXLE HOUSING OIL SEPARATOR

a.
C201327

Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.


Hide 35035 31.REMOVE FRONT OIL PUMP ASSEMBLY

a.
C201328C01
0.781,0.198 0.594,0.198 false 0.448,0.125 0.604,0.313 0.156,0.188 10 *1
*1 Gasket


Remove the gasket from the front oil pump assembly.


b.

Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.


c.
C201329

Remove the front oil pump body O-ring from the front oil pump assembly.


d.
C293929C01
0.344,2.74 0.625,2.74 false 0.188,2.656 0.5,2.854 0.313,0.198 10 false *1
*1 Thrust Bearing Race


Remove the thrust bearing race from the underdrive planetary gear assembly.


e.
C293927C04
1.365,0.302 1.542,0.302 1.542,0.302 1.74,0.625 false 0.833,1.104 1.24,1.104 false 1.188,0.208 1.5,0.365 0.313,0.156 10 false *1 0.667,1 0.979,1.156 0.313,0.156 10 false *2
*1 Thrust Needle Roller Bearing
*2 O-ring


Remove the thrust needle roller bearing from the counter drive gear nut.


f.

Remove the O-ring from the transaxle case sub-assembly.


Hide 35683B 32.REMOVE NO. 3 BRAKE DISC

a.
C317753C01
1.802,1 2.135,1.656 2.135,1.656 2.281,1.656 true 2.323,1.563 2.625,1.875 0.302,0.313 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front oil pump assembly.


b.
C317152C01
2.115,0.375 2.667,0.375 false 0.76,2.031 1.313,2.031 false 0.75,0.979 1.302,0.979 false 1.01,0.99 1.01,1.438 1.01,1.438 1.302,1.438 false 2.125,1.198 2.406,1.198 false 2.135,0.74 2.406,0.74 2.406,0.74 2.406,1.667 false 2.115,1.667 2.667,1.667 false 2.708,0.292 3.073,0.583 0.365,0.292 10 false *1 0.573,0.906 0.896,1.146 0.323,0.24 10 false *2 2.74,1.583 3.177,1.917 0.438,0.333 10 false *3 0.583,1.958 0.948,2.25 0.365,0.292 10 false *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.


Hide 34330 34.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C293913

Remove the underdrive planetary gear assembly from the front oil pump assembly.


Hide 35663 35.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C202906C01
1.146,0.208 1.271,0.208 1.271,0.208 1.469,0.344 false 1.188,1.115 1.271,1.115 1.271,1.115 1.469,0.948 false 1.01,0.125 1.188,0.292 0.177,0.167 10 false *1 1.031,1.052 1.271,1.365 0.24,0.313 10 false *2
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing and thrust bearing race from the underdrive planetary gear assembly.


Hide 35706V 36.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C201331C01
1.271,0.302 1.385,0.302 1.385,0.302 1.646,0.854 false 1.552,3.031 1.26,3.031 false 2.438,1.396 2.333,1.396 2.333,1.396 1.979,2.146 false 1.115,0.219 1.281,0.385 0.167,0.167 10 false *1 1.104,2.948 1.292,3.115 0.188,0.167 10 false *3 2.469,1.313 2.667,1.49 0.198,0.177 10 false *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


While expanding the snap ring with a snap ring expander, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 35701 39.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C293914

Remove the input shaft sub-assembly from the front oil pump assembly.


b.
C202905C01
1.156,1.01 1.344,1.01 false 0.938,2.208 1.479,2.208 false 1.719,2.802 2.333,2.479 2.333,2.479 1.74,3.135 false 1.74,2.979 2.333,2.479 false 1.115,0.188 1.25,0.188 1.25,0.188 1.427,0.365 false 0.969,0.094 1.125,0.271 0.156,0.177 10 *1 0.979,0.906 1.167,1.26 0.188,0.354 10 *2 0.771,2.115 0.938,2.302 0.167,0.188 10 *3 2.365,2.375 2.583,2.552 0.219,0.177 10 *4
*1 Thrust Bearing Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Sub-assembly
*4 Oil Seal Ring


Remove the thrust needle roller bearing and thrust bearing race from the input shaft sub-assembly.


c.

Using a screwdriver with its tip wrapped with protective tape, remove the 3 oil seal rings from the input shaft sub-assembly.


Hide 34321 40.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C293915C01
0.5,0.583 0.938,0.583 false 0.521,1.24 0.979,1.24 false 0.344,0.5 0.656,0.656 0.313,0.156 10 false *1 0.365,1.146 0.677,1.302 0.313,0.156 10 false *2
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Remove the underdrive planetary sun gear from the front oil pump assembly.


b.

Remove the thrust needle roller bearing from the front oil pump assembly.


Hide 35681 41.REMOVE NO. 1 BRAKE DISC

a.
C293916C01
0.729,0.917 1.24,0.917 false 2.198,0.573 2.708,0.573 false 2.49,0.583 2.49,1.167 2.49,1.167 2.177,1.167 false 2.75,0.5 3.063,0.656 0.313,0.156 10 false *1 0.563,0.833 0.875,0.99 0.313,0.156 10 false *2
*1 Snap Ring
*2 Brake Snap Ring Stopper


Using a screwdriver with its tip wrapped with protective tape, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.


b.
C317153C01
1.438,1.26 1.938,1.26 false 1.708,1.26 1.708,2.208 1.708,2.208 1.938,2.208 false 1.708,1.708 1.938,1.708 false 2.948,1.958 2.948,1.042 2.948,1.042 2.76,1.042 false 2.719,0.573 3.073,0.573 false 2.76,1.958 3.104,1.958 false 2.76,1.479 2.948,1.479 false 3.104,0.49 3.344,0.74 0.24,0.25 10 false *1 1.26,1.177 1.594,1.438 0.333,0.26 10 false *2 3.146,1.875 3.375,2.146 0.229,0.271 10 false *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Remove the No. 1 brake flange, 3 No. 1 brake discs and 3 No. 1 brake plates from the front oil pump assembly.


Hide 35608L 43.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C293918

Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.


Hide 35608L 44.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621F 45.REMOVE NO. 1 BRAKE PISTON

a.
C293919

While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.


b.
C319480C01
1.458,1.427 1.542,1.271 1.542,1.271 1.698,1.271 false 1.958,0.677 2.042,0.521 2.042,0.521 2.198,0.521 false 1.74,1.167 2.052,1.323 0.313,0.156 10 false *1 2.229,0.427 2.542,0.583 0.313,0.156 10 false *1
*1 O-ring


Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 1 brake piston.


Hide 41311 46.REMOVE FRONT DIFFERENTIAL CASE

a.
C201332

Remove the front differential case from the transaxle case sub-assembly.


Hide 41311E 47.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C317735C02
1.969,1.594 1.969,1.146 1.969,1.146 2.198,1.146 false 1.969,1.354 2.177,1.354 false 2.583,1.177 2.406,0.74 2.406,0.74 2.229,0.74 false 2.063,0.198 2.375,0.396 0.313,0.198 10 false *a 0.083,0.646 0.396,0.906 0.313,0.26 10 false *b 1.917,0.656 2.396,0.917 0.479,0.26 10 false SST 1.844,1.625 2.323,1.885 0.479,0.26 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case.

SST
09950-00020  
09950-00030  
09950-60011  (09951-00480)


Hide 41311F 48.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C317736C02
2.708,1.083 2.958,0.531 2.958,0.531 2.271,0.813 true 1.417,0.146 1.729,0.354 0.313,0.208 10 false *a 0.052,0.76 0.313,1 0.26,0.24 10 false *b 3.021,0.406 3.406,0.656 0.385,0.25 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60011  (09951-00480)


Hide 35782H 49.REMOVE COUNTER DRIVE GEAR NUT

a.
C201333N09
0.867,0.065 1.19,0.228 0.323,0.163 10 SST 1.245,0.158 1.339,0.158 1.339,0.158 1.912,0.873 false

Using SST and a hammer, release the staked part of the front planetary gear assembly.

SST
09930-00010  


b.
C299140N01
1.479,4.042 1.771,4.333 0.292,0.292 10 false P

Turn the manual valve lever shaft sub-assembly counterclockwise to set it to the P position as shown in the illustration.


c.
C201527N09
0.546,0.23 0.882,0.405 0.336,0.175 10 SST 0.933,0.299 1.039,0.299 1.039,0.299 1.838,1.012 false

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


d.
C299141N01
1.458,4.073 1.729,4.333 0.271,0.26 10 false N

Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.


Hide 35783R 50.REMOVE COUNTER DRIVEN GEAR

a.
C201336

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 41211J 51.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE)

a.
C324774C01
1.417,0.594 1.615,0.719 1.615,0.719 1.385,1.24 true 1.021,1.24 1.604,0.719 true 1.656,0.021 1.969,0.177 0.313,0.156 10 false *a 0.042,0.656 0.354,0.813 0.313,0.156 10 false *b 1.667,0.625 2.125,0.823 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the differential drive pinion tapered roller bearing RH (inner race) from the counter driven gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00320)


Hide 41211K 52.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE)

HINT:

If removing the differential drive pinion tapered roller bearing LH (inner race), replace the counter driven gear with a new one.


Hide 53.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C317737N01
0.833,0.51 1.385,0.51 false 0.531,0.448 0.99,0.646 0.458,0.198 10 false SST

Using SST, remove the front differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.

SST
09308-00010  


Hide 35558 54.REMOVE PAWL SHAFT CLAMP

a.
C201339

Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.


Hide 35165 55.REMOVE NO. 1 TRANSMISSION CASE PLATE

a.
C201340

Remove the bolt and No. 1 transmission case plate from the transaxle case sub-assembly.


Hide 35596 56.REMOVE PAWL STOPPER PLATE

a.
C201341

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


Hide 35598 57.REMOVE PARKING LOCK SLEEVE

a.
C201342

Remove the parking lock sleeve from the transaxle case sub-assembly.


Hide 35557 58.REMOVE PARKING LOCK PAWL

a.
C201343C08
0.583,1.448 0.677,1.448 0.677,1.448 0.969,1.542 false 0.906,0.156 0.802,0.156 0.802,0.156 1.031,1.229 false 1.594,0.49 1.521,0.49 1.521,0.49 1.396,1.292 false 2.531,1.385 2.417,1.385 2.417,1.385 2.052,1.677 false 0.406,1.354 0.583,1.531 0.177,0.177 10 false *3 0.927,0.042 1.125,0.198 0.198,0.156 10 false *1 1.625,0.385 1.802,0.563 0.177,0.177 10 false *2 2.573,1.281 2.729,1.448 0.156,0.167 10 false *4
*1 Parking Lock Pawl Pin
*2 Parking Lock Pawl Shaft
*3 Spring
*4 Parking Lock Pawl


Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.


Hide 59.REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE)

a.
C201344N05
1.029,0.444 1.361,0.594 0.332,0.15 10 SST 1.401,0.531 1.804,0.531 false

Using SST, remove the differential drive pinion tapered roller bearing LH (outer race) from the transaxle case sub-assembly.

SST
09308-00010  


Hide 43420H 60.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C138709N05
1.333,1.302 0.5,1.771 0.5,1.771 1.229,1.563 false 0.177,1.708 0.5,1.896 0.323,0.188 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.

SST
09950-60011  (09951-00650)
09950-70010  (09951-07100)


Hide 35790 61.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C317754C01
2.302,1.167 1.958,0.365 1.958,0.365 1.813,0.365 true 1.625,0.292 1.896,0.573 0.271,0.281 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.


b.
C141526C09
1.781,1.094 2.323,1.094 false 0.75,0.354 1.198,0.354 false 2.365,0.979 2.573,1.146 0.208,0.167 10 false *2 0.594,0.271 0.781,0.417 0.188,0.146 10 false *1
*1 One-way Clutch Assembly with Planetary Ring Gear
*2 Thrust Needle Roller Bearing


Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.


c.

Remove the thrust needle roller bearing from the front planetary gear assembly.


d.
C201345C01
0.875,0.135 0.969,0.135 0.969,0.135 1.271,0.417 false 1.115,1.438 1.375,1.438 false 2.521,1 2.802,1.073 2.802,1.073 2.802,1.156 false 0.719,0.042 0.875,0.229 0.156,0.188 10 false *1 0.948,1.344 1.115,1.521 0.167,0.177 10 false *3 2.75,1.156 2.938,1.354 0.188,0.198 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Remove the one-way clutch assembly from the planetary ring gear.


e.

Remove the outer race retainer from the one-way clutch assembly.


Hide 35762E 63.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480C01
1.26,0.646 0.958,0.646 false 0.938,2.292 1.198,2.292 false 2.125,1.375 2.438,1.375 false 0.771,2.177 0.948,2.344 0.177,0.167 10 *3 2.479,1.26 2.646,1.417 0.167,0.156 10 *2 0.802,0.531 0.979,0.698 0.177,0.167 10 *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the planetary ring gear.


b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35682A 64.REMOVE NO. 2 BRAKE DISC

a.
C317755C01
2.167,1.125 1.813,0.302 1.813,0.302 1.646,0.302 true 1.458,0.219 1.802,0.542 0.344,0.323 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.


b.
C238853C01
1.333,0.969 1.177,0.969 1.177,0.969 1.177,1.75 false 1.177,1.75 1.333,1.75 false 1.323,1.229 1.177,1.229 false 1.323,1.479 1.177,1.479 false 1.177,1.354 1.063,1.354 false 2.177,0.552 2.323,0.552 false 2.208,0.802 2.375,0.802 2.375,0.802 2.375,1.573 false 2.375,1.573 2.208,1.573 false 2.208,1.063 2.375,1.063 false 2.208,1.323 2.375,1.323 false 2.375,1.188 2.458,1.188 false 2.5,1.115 2.667,1.292 0.167,0.177 10 *3 0.885,1.292 1.042,1.469 0.156,0.177 10 *2 2.365,0.479 2.531,0.656 0.167,0.177 10 *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Remove the No. 2 brake flange, 4 No. 2 brake discs and 4 No. 2 brake plates from the transaxle case sub-assembly.


Hide 35068C 66.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C317756C01
1.563,0.25 1.719,0.25 1.719,0.25 2.146,1.156 true 1.365,0.156 1.729,0.417 0.365,0.26 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.


b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.


Hide 67.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35622G 68.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the No. 2 brake piston from the transaxle case sub-assembly.


b.
C319481C01
1.51,0.594 1.333,0.26 1.333,0.26 1.156,0.26 true 2.094,1.344 2.031,1.125 2.031,1.125 1.906,1.125 true 0.99,0.177 1.302,0.333 0.313,0.156 10 false *1 1.719,1.031 2.031,1.188 0.313,0.156 10 false *1
*1 O-ring


Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 2 brake piston.


Hide 35720 69.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674N05
2.62,1.242 2.966,1.407 0.346,0.166 10 SST 1.76,1.752 2.585,1.334 2.585,1.334 1.884,2.015 false

Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.

SST
09950-60011  (09951-00580)
09950-70010  (09951-07100)


Hide 35782C 70.REMOVE COUNTER DRIVE GEAR

a.
C293937N01
1.281,3.083 1.854,2.594 1.854,2.594 0.979,2.417 false 1.823,1.167 2.625,0.385 2.625,0.385 1.719,1 true 2.708,0.292 3.167,0.49 0.458,0.198 10 false SST 1.938,2.5 2.396,2.698 0.458,0.198 10 false SST

Using SST and a press, remove the counter drive gear with counter drive gear bearing inner race (front side) from the transaxle case sub-assembly.

SST
09950-60021  (09951-00710)
09950-70010  (09951-07100)


b.

Remove the counter drive gear bearing inner race (rear side).


c.

Remove the 2 counter drive gear bearings (balls and cage) from the counter drive gear bearing (outer race).


d.
C201348

As shown in the illustration, tighten 2 service bolts evenly to make a clearance of approximately 5.0 mm (0.197 in.) between the counter drive gear and counter drive gear bearing inner race (front side).


e.
C201349C01
0.272,1.178 0.612,1.336 0.34,0.158 10 *b 2.408,0.063 2.712,0.221 0.305,0.158 10 *a 0.254,1.729 0.563,1.889 0.308,0.161 10 SST 0.835,1.535 0.614,1.783 0.614,1.783 1.279,1.363 false 1.253,1.545 0.627,1.775 false 0.88,1.221 0.614,1.783 false
*a Turn
*b Hold


Using SST, remove the counter drive gear bearing inner race (front side) from the counter drive gear.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60021  (09951-00710)


Hide 35623 71.REMOVE NO. 3 BRAKE PISTON

a.
C201350N05
1.491,0.214 1.79,0.362 0.299,0.148 10 SST 1.839,0.302 1.931,0.302 1.931,0.302 2.078,0.603 false

Place SST on the No. 3 brake piston return spring sub-assembly and compress the No. 3 brake piston return spring sub-assembly with a press.

SST
09387-00070  


b.

Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.


c.
C317911C01
1.708,0.792 1.396,0.167 1.396,0.167 1.26,0.167 true 1.063,0.094 1.427,0.365 0.365,0.271 10 false *1
*1 No. 3 Brake Piston Return Spring Sub-assembly


Remove the No. 3 brake piston return spring sub-assembly from the transaxle case sub-assembly.


d.
C317912C01
1.656,0.677 1.313,0.135 1.313,0.135 1.146,0.135 true 0.938,0.063 1.25,0.292 0.313,0.229 10 false *1
*1 No. 3 Brake Piston


Remove the No. 3 brake piston from the transaxle case sub-assembly.


e.
C317138C01
1.906,0.365 2.052,0.125 2.052,0.125 2.333,0.125 false 2.104,1.177 2.021,0.927 2.021,0.927 1.927,0.927 false 2.396,0.042 2.708,0.198 0.313,0.156 10 false *1 1.781,0.844 2.094,1 0.313,0.156 10 false *1
*1 O-ring


Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 3 brake piston.


Hide 72.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35409 73.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, manual detent spring cover and manual detent spring sub-assembly from the transaxle case sub-assembly.


Hide 35501 74.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355

Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

HINT:

Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



Hide 35506 75.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.


b.
C201357

Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.


Hide 35506F 76.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C317757C01
2.396,0.625 2.479,0.625 2.479,0.625 2.573,0.833 true 2.219,0.531 2.49,0.792 0.271,0.26 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.