Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351197 OIL PUMP G

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  INSPECTION  


PROCEDURE

Hide 35035 1.INSPECT FRONT OIL PUMP ASSEMBLY

a.
C138512

Turn the front oil pump drive gear with 2 screwdrivers and check that it rotates smoothly.

NOTICE:

Be careful not to damage the oil seal lip.



Hide 2.INSPECT CLEARANCE OF FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY

a.

Inspect the body clearance.

i.
C316895

Push the front oil pump driven gear to one side of the front oil pump body sub-assembly.


ii.

Using a feeler gauge, measure the body clearance.

Standard Clearance:

0.12 to 0.17 mm (0.00472 to 0.00669 in.)


Maximum Clearance:

0.17 mm (0.00669 in.)


If the clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.



b.

Inspect the side clearance.

i.
C316896

Using a straightedge and feeler gauge, measure the side clearance of both gears.

Standard Side Clearance:

0.035 to 0.05 mm (0.00138 to 0.00197 in.)


Maximum Side Clearance:

0.05 mm (0.00197 in.)


If the clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.

HINT:

There are 4 front oil pump drive gears and front oil pump driven gears of different thicknesses.


Front Oil Pump Drive Gear Thickness
Part No. Mark Thickness (mm (in.))
35321-33160 A 11.554 to 11.56 (0.45488 to 0.45512)
35321-33170 B 11.561 to 11.567 (0.45516 to 0.45539)
35321-33180 C 11.568 to 11.574 (0.45543 to 0.45567)
35321-33190 D 11.575 to 11.581 (0.45571 to 0.45594)

Front Oil Pump Driven Gear Thickness
Part No. Mark Thickness (mm (in.))
35322-33160 A 11.554 to 11.56 (0.45488 to 0.45512)
35322-33170 B 11.561 to 11.567 (0.45516 to 0.45539)
35322-33180 C 11.568 to 11.574 (0.45543 to 0.45567)
35322-33190 D 11.575 to 11.581 (0.45571 to 0.45594)



Hide 3.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

a.
C138514

Using a caliper gauge, measure the inside diameter of the front oil pump body bushing.

Standard Inside Diameter:

43.135 to 43.160 mm (1.69822 to 1.69921 in.)


Maximum Inside Diameter:

43.160 mm (1.69921 in.)


If the inside diameter is greater than the maximum, replace the front oil pump and gear body sub-assembly.


Hide 4.INSPECT STATOR SHAFT ASSEMBLY

a.
C138513

Using a caliper gauge, measure the inside diameter of the stator shaft bushing.

Standard Inside Diameter:

22.500 to 22.526 mm (0.88583 to 0.88685 in.)


Maximum Inside Diameter:

22.526 mm (0.88685 in.)


If the inside diameter is greater than the maximum, replace the stator shaft assembly.