Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351198 DIFFERENTIAL CASE G

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41311 1.INSPECT FRONT DIFFERENTIAL CASE

a.
C317738N01
2.76,2.875 2.583,2.875 2.583,2.875 2.583,2.385 false 2.823,2.781 3.219,3.042 0.396,0.26 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05030)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all of the following inspections.

·

If the front differential side gear still locks after replacing the malfunctioning parts, replace the front differential case.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Install SST as shown in the illustration and tighten it.

C317739C01
4.688,0.271 5.125,0.271 false 5.115,1.667 4.896,1.521 4.896,1.521 5.104,1.396 false 4.396,1.521 4.896,1.521 false 3.24,0.573 3.563,0.823 0.323,0.25 10 false *a 0.74,2.552 1.063,2.771 0.323,0.219 10 false *b 4.396,0.188 5.052,0.479 0.656,0.292 10 false SST 4.094,1.448 4.75,1.74 0.656,0.292 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C317740C01
2.552,0.198 2.833,0.198 false 2.875,0.104 3.198,0.438 0.323,0.333 10 false *1
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


d.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.20 mm (0.00787 in.) or less


If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

HINT:

Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.


Front No. 1 Differential Side Gear Thrust Washer Thickness:
Part No. Thickness (mm (in.))
41361-33340 0.90 (0.0354)
41361-33350 0.95 (0.0374)
41361-33360 1.00 (0.0394)
41361-33370 1.05 (0.0413)
41361-33380 1.10 (0.0433)
41361-33390 1.15 (0.0453)
41361-33400 1.20 (0.0472)
41361-33410 1.25 (0.0492)


Hide 41351F 3.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.90 mm (0.0354 in.)


HINT:

Measure the most worn portion of the front differential pinion thrust washer.


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 4.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C199374

Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

17.975 mm (0.708 in.)


HINT:

Measure the most worn portion of the front No. 1 differential pinion shaft.


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.