Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (except 2AR-FE) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0326622 CRUISE CONTROL SYSTEM(except 2AR-FE) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(except 2AR-FE)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake pedal is depressed, voltage is applied to the terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the engine switch is on (IG) and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

A421218E01
0.198,0.719 2.188,0.917 1.99,0.198 10 false from AM2 Fuse 0.219,1.229 1.156,1.625 0.938,0.396 10 false from IG2-NO. 2 Relay 2.104,0.875 4.094,1.073 1.99,0.198 10 false STOP 1.813,1.396 3.802,1.594 1.99,0.198 10 false ECU-IG2 NO. 3 3.125,0.635 3.281,0.865 0.156,0.229 10 false 7 3.115,1.135 3.271,1.365 0.156,0.229 10 false 6 3.115,1.635 3.271,1.865 0.156,0.229 10 false 2 3.281,0.74 3.438,0.969 0.156,0.229 10 false B 3.271,1.229 3.427,1.458 0.156,0.229 10 false B 3.271,1.75 3.719,2.031 0.448,0.281 10 false GND 3.885,1.406 4.042,1.635 0.156,0.229 10 false L 3.896,0.615 4.052,0.844 0.156,0.229 10 false L 5.792,0.5 6.333,0.74 0.542,0.24 10 false STP 5.792,1.281 6.333,1.521 0.542,0.24 10 false ST1- 4.052,0.51 4.208,0.74 0.156,0.229 10 false 3 4.052,1.292 4.208,1.521 0.156,0.229 10 false 5 4.063,2.76 4.302,3.01 0.24,0.25 10 false 42 3.708,2.854 4.25,3.094 0.542,0.24 10 false STP 5.802,2.875 6.344,3.115 0.542,0.24 10 false STP1*2 3.719,3.906 4.26,4.146 0.542,0.24 10 false STP 2.698,2.094 4.688,2.292 1.99,0.198 10 false Stop Light Switch Assembly 2.417,2.104 4.406,2.302 1.99,0.198 10 false A37 1.771,3.219 4.833,3.479 3.063,0.26 10 false Skid Control ECU (Brake Actuator Assembly) 1.51,3.219 3.5,3.417 1.99,0.198 10 false A34 3.177,4.271 5.031,4.615 1.854,0.344 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 2.333,4.271 4.323,4.469 1.99,0.198 10 false K28*1, K27*2 5.271,3.24 6.771,3.427 1.5,0.188 10 false R8 5.479,3.24 7.021,3.625 1.542,0.385 10 false Certification ECU (Smart Key ECU Assembly)*2 5.573,2.76 5.813,3 0.24,0.24 10 false 25 4.792,0.51 6.781,0.708 1.99,0.198 10 false 21*3, 27*4, 9*5 4.708,1.302 6.698,1.5 1.99,0.198 10 false 22*3, 42*4, 10*5 6.198,2.104 6.74,2.344 0.542,0.24 10 false ECM 4.896,2.104 6.885,2.302 1.99,0.198 10 false A24*3, A23*4, A78*5 0.042,3.594 3.104,3.854 3.063,0.26 10 false *1: w/o Smart Entry and Start System 0.042,3.823 3.104,4.083 3.063,0.26 10 false *2: w/ Smart Entry and Start System 0.042,4.063 3.104,4.323 3.063,0.26 10 false *3: for A25A-FKS 0.042,4.302 3.104,4.563 3.063,0.26 10 false *4: for 2GR-FKS 0.031,4.542 3.094,4.802 3.063,0.26 10 false *5: for 6AR-FSE 4.052,3.802 6.042,4 1.99,0.198 10 false 8*1, 4*2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A395526C06
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.552,0.344 2.01,0.542 0.458,0.198 10 false A37
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A37 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V
A37-6 (B) - Body ground Engine switch on (IG) 11 to 14 V
A37-6 (B) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A24 ECM connector (for A25A-FKS).


b.

Disconnect the A23 ECM connector (for 2GR-FKS).


c.

Disconnect the A78 ECM connector (for 6AR-FSE).


d.

Disconnect the A37 stop light switch assembly connector.


e.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


f.

Disconnect the R8 certification ECU (smart key ECU assembly) connector (w/ Smart Entry and Start System).


g.

Disconnect the K28 shift lock control ECU (shift lock control unit assembly) connector (w/o Smart Entry and Start System).


h.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector (w/ Smart Entry and Start System).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for A25A-FKS):
Tester Connection Condition Specified Condition
A24-22 (ST1-) - A37-5 (L) Always Below 1 Ω
A24-21(STP) - A37-3 (L) Always Below 1 Ω
A24-22 (ST1-) or A37-5 (L) - Body ground Always 10 kΩ or higher
A24-21 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher


Standard Resistance (for 2GR-FKS):
Tester Connection Condition Specified Condition
A23-42 (ST1-) - A37-5 (L) Always Below 1 Ω
A23-27 (STP) - A37-3 (L) Always Below 1 Ω
A23-42 (ST1-) or A37-5 (L) - Body ground Always 10 kΩ or higher
A23-27 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher


Standard Resistance (for 6AR-FSE):
Tester Connection Condition Specified Condition
A78-10 (ST1-) - A37-5 (L) Always Below 1 Ω
A78-9 (STP) - A37-3 (L) Always Below 1 Ω
A78-10 (ST1-) or A37-5 (L) - Body ground Always 10 kΩ or higher
A78-9 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR