Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2018.04
RM33A0E _59 Vehicle Exterior _065393 MIRROR (EXT) _0327582 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

a.

Check the operation of the mirror surface. (for 11 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319979C15
2.49,2.531 2.49,1.948 2.49,1.948 2.292,1.948 false 2.583,2.531 2.583,1.531 2.583,1.531 2.781,1.531 false 2.698,2.531 2.698,1.948 2.698,1.948 2.896,1.948 false 2.052,1.865 2.313,2.042 0.26,0.177 10 false MH 2.813,1.458 3.094,1.656 0.281,0.198 10 false M+ 2.927,1.875 3.208,2.156 0.281,0.281 10 false MV 1.479,2.396 1.646,2.542 0.167,0.146 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror surface. (for 7 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319940C08
2.042,2.375 2.042,1.948 2.042,1.948 2.188,1.948 false 1.948,2.375 1.948,1.604 1.948,1.604 2.188,1.604 false 1.833,2.406 1.833,1.833 1.833,1.833 1.688,1.833 false 1.271,2.406 1.719,2.74 0.448,0.333 10 false *a 1.427,1.76 1.938,2.156 0.51,0.396 10 false MV 2.25,1.854 2.885,2.167 0.635,0.313 10 false MH 2.25,1.521 2.74,1.823 0.49,0.302 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 7 (M+)
Turns upward
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 3 (MV)
Turns downward
Battery positive (+) → Terminal 6 (MH)
Battery negative (-) → Terminal 7 (M+)
Turns left
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 6 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the mirror surface. (for 16 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B485586C03
0.958,1.896 1.219,1.896 1.219,1.896 1.219,2.573 false 0.917,3.208 1.219,3.208 1.219,3.208 1.219,2.771 false 1.615,3.208 1.313,3.208 1.313,3.208 1.313,2.771 false 0.688,1.833 1,2.031 0.313,0.198 10 false MV 1.552,1.75 1.865,1.948 0.313,0.198 10 false *a 0.646,3.125 0.958,3.323 0.313,0.198 10 false MH 1.677,3.125 1.99,3.323 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns left
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



d.

Check the operation of the mirror surface. (for 22 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B495592C02
2.563,2.552 2.563,1.969 2.563,1.969 2.729,1.969 true 2.49,2.552 2.49,1.719 2.49,1.719 2.74,1.719 true 2.406,2.552 2.406,1.885 2.406,1.885 2.24,1.885 true 2.833,1.885 3.146,2.083 0.313,0.198 10 false MH 2.833,1.635 3.146,1.833 0.313,0.198 10 false M+ 1.969,1.802 2.281,2 0.313,0.198 10 false MV 1.615,2.094 1.927,2.292 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward
Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns right
Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly RH.



e.

Check the operation of the mirror heater. (for 11 Pin Connector, w/ Mirror Heater)

i.
B319983C17
2.563,2.781 2.563,3.094 2.563,3.094 2.167,3.094 false 2.01,2.5 2.01,1.875 2.01,1.875 1.615,1.875 false 1.469,1.802 1.667,1.99 0.198,0.188 10 false + 2.042,3.031 2.313,3.25 0.271,0.219 10 false E 1.302,2.25 1.563,2.458 0.26,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 11 (E) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 2 (+) and the negative (-) battery terminal to terminal 11 (E), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



f.

Check the operation of the mirror heater. (for 16 Pin Connector)

i.
B485587C03
2.031,2.625 2.031,1.854 2.031,1.854 2.427,1.854 false 2.458,3.167 2.031,3.167 2.031,3.167 2.031,2.792 false 0.708,2.021 1.021,2.219 0.313,0.198 10 false *a 2.49,1.771 2.802,1.969 0.313,0.198 10 false + 2.542,3.073 2.854,3.271 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (+) - 15 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 7 (+) and the negative (-) battery terminal to terminal 15 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



g.

Check the operation of the mirror heater. (for 22 Pin Connector)

i.
B495593C02
2.333,2.563 2.333,1.979 2.333,1.979 2.5,1.979 true 2.167,3.302 2.333,3.302 2.333,3.302 2.333,2.719 true 2.583,1.885 2.74,2.083 0.156,0.198 10 false + 2.042,3.198 2.198,3.396 0.156,0.198 10 false - 1.635,2.094 1.938,2.292 0.302,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 17 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 6 (+) and the negative (-) battery terminal to terminal 17 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



h.

Check the operation of the retractable mirror. (for 11 Pin Connector, w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B320731C16
0.813,2.792 0.813,3.146 0.813,3.146 0.615,3.146 false 0.552,2.021 0.813,2.021 0.813,2.021 0.823,2.573 false 2.688,0.042 2.917,0.281 0.229,0.24 10 false *a 1.99,2.292 2.25,2.5 0.26,0.208 10 false *e 2.406,2.063 2.604,2.208 0.198,0.146 10 false *d 2.865,1.792 3.073,2.01 0.208,0.219 10 false *c 3,0.917 3.25,1.146 0.25,0.229 10 false *b 0.375,3.083 0.688,3.292 0.313,0.208 10 false MF 0.313,1.958 0.688,2.167 0.375,0.208 10 false MR 1.146,1.927 1.458,2.188 0.313,0.26 10 false *f
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



i.

Check the operation of the retractable mirror. (for 7 Pin Connector, w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B504673C01
0.5,3.25 0.667,3.25 0.667,3.25 0.667,2.708 false 0.938,3.25 0.771,3.25 0.771,3.25 0.771,2.688 false 2.615,0.104 2.927,0.302 0.313,0.198 10 false *a 2.958,0.948 3.271,1.146 0.313,0.198 10 false *b 2.854,1.823 3.167,2.021 0.313,0.198 10 false *c 2.385,2.042 2.698,2.24 0.313,0.198 10 false *d 2.031,2.281 2.344,2.479 0.313,0.198 10 false *e 0.313,2.042 0.625,2.24 0.313,0.198 10 false *f 0.271,3.156 0.583,3.354 0.313,0.198 10 false MF 0.979,3.156 1.292,3.354 0.313,0.198 10 false MR
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



j.

Check the operation of the retractable mirror. (for 16 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B509871C02
1.583,3.75 1.583,3 1.583,3 2.583,3 false 1.583,3.917 1.583,4.333 1.583,4.333 2.583,4.333 false 1.948,0.271 2.26,0.427 0.313,0.156 10 false *a 2.344,1.104 2.656,1.26 0.313,0.156 10 false *b 2.188,2.104 2.5,2.26 0.313,0.156 10 false *c 1.792,2.323 2.104,2.479 0.313,0.156 10 false *d 1.365,2.521 1.677,2.677 0.313,0.156 10 false *e 0.802,3.156 1.115,3.313 0.313,0.156 10 false *f 2.635,2.917 2.948,3.073 0.313,0.156 10 false MR 2.625,4.25 2.938,4.406 0.313,0.156 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



k.

Check the operation of the retractable mirror. (for 22 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B495594C02
1.167,2.813 1.167,3.229 1.167,3.229 1.333,3.229 true 1.083,2.813 1.083,3.229 1.083,3.229 0.917,3.229 true 0.208,2.177 0.521,2.375 0.313,0.198 10 false *f 0.646,3.146 0.958,3.344 0.313,0.198 10 false MR 2.667,0.135 2.979,0.333 0.313,0.198 10 false *a 2.99,0.969 3.302,1.167 0.313,0.198 10 false *b 2.844,1.813 3.156,2.01 0.313,0.198 10 false *c 2.469,2.115 2.781,2.313 0.313,0.198 10 false *d 2.083,2.333 2.396,2.531 0.313,0.198 10 false *e 1.438,3.146 1.75,3.344 0.313,0.198 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

a.

Check the operation of the mirror surface. (for 11 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319980C15
1.49,2.521 1.49,1.844 1.49,1.844 1.75,1.844 false 1.385,2.521 1.385,1.615 1.385,1.615 1.167,1.615 false 1.281,2.521 1.281,1.896 1.281,1.896 1.063,1.896 false 1.802,1.76 2.125,1.969 0.323,0.208 10 false MV 0.948,1.542 1.229,1.729 0.281,0.188 10 false M+ 0.833,1.823 1.135,2.031 0.302,0.208 10 false MH 0.281,2.198 0.531,2.385 0.25,0.188 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns right
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror surface. (for 7 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B319941C10
0.958,2.354 0.958,1.969 0.958,1.969 1.146,1.969 false 0.865,2.365 0.865,1.573 0.865,1.573 1.156,1.573 false 0.76,2.385 0.76,1.885 0.76,1.885 0.531,1.885 false 1.75,2.427 2.354,2.802 0.604,0.375 10 false *a 0.271,1.823 0.75,2.115 0.479,0.292 10 false MV 1.219,1.49 1.708,1.771 0.49,0.281 10 false M+ 1.24,1.885 1.865,2.188 0.625,0.302 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 7 (M+)
Turns upward
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 3 (MV)
Turns downward
Battery positive (+) → Terminal 6 (MH)
Battery negative (-) → Terminal 7 (M+)
Turns left
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 6 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the mirror surface. (for 16 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B485588C03
0.99,1.854 1.271,1.854 1.271,1.854 1.271,2.563 false 0.979,3.177 1.271,3.177 1.271,3.177 1.271,2.74 false 1.635,3.177 1.375,3.177 1.375,3.177 1.375,2.74 false 1.604,1.76 1.917,1.958 0.313,0.198 10 false *a 0.729,1.792 1.042,1.99 0.313,0.198 10 false MV 0.719,3.104 1.031,3.302 0.313,0.198 10 false MH 1.688,3.104 2,3.302 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns right
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



d.

Check the operation of the mirror surface. (for 22 Pin Connector)

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B495595C02
1.354,2.552 1.354,1.969 1.354,1.969 1.521,1.969 true 1.198,2.552 1.198,1.885 1.198,1.885 1.031,1.885 true 1.281,2.552 1.281,1.719 1.281,1.719 1.51,1.719 true 1.583,1.885 1.896,2.083 0.313,0.198 10 false MH 0.333,2.042 0.646,2.24 0.313,0.198 10 false *a 0.781,1.802 1.094,2 0.313,0.198 10 false MV 1.583,1.635 1.896,1.833 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 8 (M+)
Turns upward
Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 8 (M+)
Turns left
Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



e.

Check the operation of the mirror heater. (for 11 Pin Connector, w/ Mirror Heater)

i.
B319984C19
0.854,2.563 0.854,1.969 0.854,1.969 1.094,1.969 false 1.417,2.833 1.417,3.219 1.417,3.219 1.656,3.219 false 1.729,3.146 1.875,3.323 0.146,0.177 10 false E 1.177,1.906 1.604,2.333 0.427,0.427 10 false + 0.292,2.271 0.583,2.479 0.292,0.208 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 11 (E) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 2 (+) and the negative (-) battery terminal to terminal 11 (E), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



f.

Check the operation of the mirror heater. (for 16 Pin Connector)

i.
B485589C03
2.031,2.625 2.031,1.865 2.031,1.865 2.448,1.865 false 2.031,2.76 2.031,3.177 2.031,3.177 2.469,3.177 false 0.719,1.875 1.031,2.073 0.313,0.198 10 false *a 2.521,1.781 2.833,1.979 0.313,0.198 10 false + 2.542,3.073 2.854,3.271 0.313,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (+) - 15 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 7 (+) and the negative (-) battery terminal to terminal 15 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



g.

Check the operation of the mirror heater. (for 22 Pin Connector)

i.
B495596C02
1.125,2.542 1.125,1.958 1.125,1.958 1.292,1.958 true 1.125,2.719 1.125,3.302 1.125,3.302 0.958,3.302 true 0.365,2.083 0.615,2.313 0.25,0.229 10 false *a 1.375,1.875 1.531,2.073 0.156,0.198 10 false + 0.854,3.198 1.01,3.396 0.156,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 17 (-) 25°C (77°F) 10 to 17 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 6 (+) and the negative (-) battery terminal to terminal 17 (-), then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



h.

Check the operation of the retractable mirror. (for 11 Pin Connector, w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B320733C18
2.156,2.74 2.156,3.104 2.156,3.104 1.958,3.104 false 2.156,2.531 2.156,2.031 2.156,2.031 2.323,2.031 false 0.635,0.063 0.813,0.219 0.177,0.156 10 false *a 0.26,0.813 0.438,0.969 0.177,0.156 10 false *b 0.417,1.76 0.594,1.917 0.177,0.156 10 false *c 0.854,2.021 1.031,2.177 0.177,0.156 10 false *d 1.26,2.26 1.438,2.417 0.177,0.156 10 false *e 2.385,1.969 2.698,2.219 0.313,0.25 10 false MR 1.74,3.042 2.021,3.271 0.281,0.229 10 false MF 1.677,2.094 1.948,2.344 0.271,0.25 10 false *f
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



i.

Check the operation of the retractable mirror. (for 7 Pin Connector, w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B504674C01
1.969,3.271 2.135,3.271 2.135,3.271 2.135,2.688 false 2.396,3.271 2.229,3.271 2.229,3.271 2.229,2.688 false 0.667,0.063 0.979,0.26 0.313,0.198 10 false *a 0.313,0.865 0.625,1.063 0.313,0.198 10 false *b 0.469,1.792 0.781,1.99 0.313,0.198 10 false *c 0.896,2.021 1.208,2.219 0.313,0.198 10 false *d 1.26,2.25 1.573,2.448 0.313,0.198 10 false *e 1.781,2.115 2.094,2.313 0.313,0.198 10 false *f 1.75,3.188 2.063,3.385 0.313,0.198 10 false MF 2.438,3.188 2.75,3.385 0.313,0.198 10 false MR
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 1 (MR)
Battery negative (-) → Terminal 2 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 1 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



j.

Check the operation of the retractable mirror. (for 16 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B509872C02
1.583,3.833 1.583,3.083 1.583,3.083 2.583,3.083 false 1.583,4 1.583,4.333 1.583,4.333 2.583,4.333 false 1.313,0.302 1.625,0.458 0.313,0.156 10 false *a 0.948,1.073 1.26,1.229 0.313,0.156 10 false *b 1.177,2.021 1.49,2.177 0.313,0.156 10 false *c 1.573,2.26 1.885,2.417 0.313,0.156 10 false *d 1.938,2.49 2.25,2.646 0.313,0.156 10 false *e 0.781,3.167 1.094,3.323 0.313,0.156 10 false *f 2.635,2.99 2.948,3.146 0.313,0.156 10 false MR 2.635,4.24 2.948,4.396 0.313,0.156 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



k.

Check the operation of the retractable mirror. (for 22 Pin Connector)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B495597C02
2.729,2.813 2.729,3.229 2.729,3.229 2.896,3.229 true 2.656,2.813 2.656,3.229 2.656,3.229 2.49,3.229 true 2.99,3.146 3.302,3.344 0.313,0.198 10 false MF 2.24,3.146 2.552,3.344 0.313,0.198 10 false MR 1.802,2.188 2.115,2.385 0.313,0.198 10 false *f 0.646,0.177 0.958,0.375 0.313,0.198 10 false *a 0.354,0.885 0.667,1.083 0.313,0.198 10 false *b 0.5,1.802 0.813,2 0.313,0.198 10 false *c 0.854,2.083 1.167,2.281 0.313,0.198 10 false *d 1.24,2.281 1.552,2.479 0.313,0.198 10 false *e
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 19 (MR)
Battery negative (-) → Terminal 20 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 20 (MF)
Battery negative (-) → Terminal 19 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.