Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2018.04–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates due to a malfunction in a power supply or charging system circuit such as the battery or alternator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C360727C74
0.292,0.281 0.698,0.542 0.406,0.26 1.49,0.938 1.854,0.344 true 2.75,1 3.083,0.354 true 1.104,1.76 0.677,1.052 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.365,0.333 0.698,0.531 0.333,0.198 10 false A34 1.792,0.177 2.427,0.365 0.635,0.188 10 false IG1 2.958,0.188 3.417,0.396 0.458,0.208 10 false GND1 0.99,1.792 1.719,1.99 0.729,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-30 (+BS) - Body ground Always 11 to 14 V
A34-30 (+BS) - A34-46 (GND1) Always 11 to 14 V
A34-36 (IG1) - Body ground Ignition switch ON 11 to 14 V
A34-36 (IG1) - A34-46 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Perform a road test.


g.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1417 is not output A
C1417 is output B



A

B