Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 6AR-FSE) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0351287 COMPRESSOR(for 6AR-FSE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 6AR-FSE)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.

Secure the cooler compressor assembly in a vise between aluminum plates.


b.
E381587

Install the magnet clutch stator with the parts aligned as shown in the illustration.


c.
E363437C01
2.448,2.344 2.76,2.542 0.313,0.198 10 false *a 2.271,2.667 2.583,2.865 0.313,0.198 10 false *b 3.042,2.667 3.354,2.865 0.313,0.198 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install a new snap ring with the chamfered side facing outward.

NOTICE:

When installing the snap ring, do not widen it excessively.



d.

Connect the connector.


e.
E363438C01
2.448,2.333 2.76,2.531 0.313,0.198 10 false *a 2.292,2.667 2.604,2.865 0.313,0.198 10 false *b 3.052,2.667 3.365,2.865 0.313,0.198 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.




f.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Use the same magnet clutch washer(s) as removed during disassembly.



g.
E390951N01
0.573,0.813 0.885,0.813 false 0.24,0.719 0.698,0.917 0.458,0.198 10 false SST

Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00270  

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub before installing the bolt.



Hide 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
E390952

Set a dial indicator to the magnet clutch hub.


b.

Connect a positive (+) lead from the battery to terminal 3 of the magnet clutch connector and a negative (-) lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard Clearance:

0.30 to 0.55 mm (0.0118 to 0.0217 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet Clutch Washer Thickness:

0.1 mm (0.00394 in.)

0.3 mm (0.0118 in.)

0.5 mm (0.0197 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



c.

Remove the compressor assembly and magnetic clutch from the vise.


Hide 88688K 3.INSTALL COOLER COMPRESSOR BRACKET

a.
E390949

Install the cooler compressor bracket with the screw.


b.

Engage the clamp.