Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  TERMINALS OF ECU  


TELEVISION CAMERA CONTROLLER


B402421N07
4.531,0.583 4.948,0.833 0.417,0.25 2.177,0.583 2.594,0.833 0.417,0.25 2.24,0.615 2.552,0.813 0.313,0.198 10 false R124 4.583,0.625 4.896,0.823 0.313,0.198 10 false R123

a.

Disconnect the R123 television camera controller connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R123-2 (+B) - R123-3 (GND1) R - W-B Power source signal Always 11 to 14 V
R123-3 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
R123-6 (IG) - R123-3 (GND1) BE - W-B IG power source signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
R123-1 (ACC) - R123-3 (GND1) L - W-B ACC power source signal Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V


c.

Reconnect the R123 television camera controller connector.


d.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R124-1 (CV+) - R124-9 (CGND) B - V Rear television camera assembly display signal input Engine switch on (IG) with the camera lens of the rear television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the rear television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
R124-2 (CV-) - R123-3 (GND1) W - W-B Rear television camera assembly ground Always Below 1 Ω
R124-4 (RCV+) - R124-18 (RGND) W - G Side television camera assembly RH display signal input Engine switch on (IG) with the camera lens of the side television camera assembly RH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the side television camera assembly RH covered, blacking out the panoramic image Pulse generation (See waveform 2)
R124-5 (RCV-) - R123-3 (GND1) R - W-B Side television camera assembly RH ground Always Below 1 Ω
R124-6 (RCB+) - R124-18 (RGND) B - G Power source to side television camera assembly RH Engine switch on (ACC) 5.5 to 7.05 V
R124-7 (RSW+) - R123-3 (GND1) BE - W-B Terminal required by law Panoramic image being displayed 0 to 2 V
Panoramic image not being displayed 5.5 to 7.05 V
R124-9 (CGND) - Body ground V - Body ground Rear television camera assembly ground (shield) Always Below 1 Ω
R124-10 (LCV+) - R124-24 (LGND) W - G Side television camera assembly LH display signal input Engine switch on (IG) with the camera lens of the side television camera assembly LH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the side television camera assembly LH covered, blacking out the panoramic image Pulse generation (See waveform 2)
R124-11 (LCV-) - R123-3 (GND1) R - W-B Side television camera assembly LH ground Always Below 1 Ω
R124-12 (LCB+) - R124-24 (LGND) B - G Power source to side television camera assembly LH Engine switch on (ACC) 5.5 to 7.05 V
R124-13 (BCV+) - R124-27 (BGND) B - R Front television camera assembly display signal input Engine switch on (IG) with the camera lens of the front television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the front television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
R124-14 (BCV-) - R123-3 (GND1) W - W-B Front television camera assembly ground Always Below 1 Ω
R124-15 (BCB+) - R124-27 (BGND) G - R Power source to front television camera assembly Engine switch on (ACC) 5.5 to 7.05 V
R124-16 (SGND) - Body ground BR - Body ground Side television camera assembly RH ground (shield) Always Below 1 Ω
R124-18 (RGND) - Body ground G - Body ground Side television camera assembly RH ground Always Below 1 Ω
R124-23 (SGND) - Body ground BR - Body ground Side television camera assembly LH ground (shield) Always Below 1 Ω
R124-24 (LGND) - Body ground G - Body ground Side television camera assembly LH ground Always Below 1 Ω
R124-25 (SGND) - Body ground BR - Body ground Front television camera assembly ground (shield) Always Below 1 Ω
R124-27 (BGND) - Body ground R - Body ground Front television camera assembly ground Always Below 1 Ω
R123-20 (BLSW) - R123-3 (GND1) G - W-B Panoramic view monitor switch switch signal Engine switch on (IG), panoramic view monitor switch not pushed 5.5 to 6.5 V
Engine switch on (IG), panoramic view monitor switch pushed Below 1 V
R123-28 (NS+) - R123-27 (NSG) B - BR Video signal Engine switch on (IG) and panoramic image being displayed Pulse generation (See waveform 3)
R123-26 (NS-) - R123-3 (GND1) W - W-B Ground Always Below 1 Ω
R123-27 (NSG) - Body ground BR - Body ground Shield ground Always Below 1 Ω


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal
·

R124-1 (CV+) - R124-9 (CGND)

·

R124-10 (LCV+) - R124-24 (LGND)

·

R124-13 (BCV+) - R124-27 (BGND)

·

R124-4 (RCV+) - R124-18 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal
·

R124-1 (CV+) - R124-9 (CGND)

·

R124-10 (LCV+) - R124-24 (LGND)

·

R124-13 (BCV+) - R124-27 (BGND)

·

R124-4 (RCV+) - R124-18 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).




iii.
E336160C01
1.115,2.26 1.01,2.833 1.01,2.833 0.896,2.833 false 1.25,2.135 1.406,2.854 1.406,2.854 1.583,2.854 false 0.229,0.313 0.542,0.51 0.313,0.198 10 false *a 0.271,1.594 0.688,1.792 0.417,0.198 10 false GND 1.625,2.771 1.938,2.969 0.313,0.198 10 false *c 0.698,2.74 1.01,2.938 0.313,0.198 10 false *b
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Synchronization Signal
*c Video Waveform


Waveform 3

Item Content
Measurement terminal R123-28 (NS+) - R123-27 (NSG)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic image being displayed

HINT:

The video waveform changes according to the image sent by the television camera controller.





REAR TELEVISION CAMERA ASSEMBLY


a.

Disconnect the m4 rear television camera assembly connector.

E366763N08
3.344,0.156 3.76,0.417 0.417,0.26 3.396,0.188 3.854,0.385 0.458,0.198 10 false m4


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m4-6 (CB+) - Body ground GR - Body ground Power source Engine switch on (ACC) 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the m4 rear television camera assembly connector.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
m4-3 (CV+) - m4-2 (CV-) B - G Video signal Engine switch on (IG) with the camera lens of the side television camera assembly RH not covered, displaying the panoramic image Pulse generation
(Refer to waveform 1)
Engine switch on (IG) with the camera lens of the rear television camera assembly covered, blacking out the panoramic image Pulse generation
(Refer to waveform 2)
m4-5 (CGND) - Body ground BR - Body ground Shield ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal m4-3 (CV+) - m4-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal m4-3 (CV+) - m4-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY


E367990E02
1.448,0.25 1.865,0.5 0.417,0.25 3.375,0.25 3.792,0.5 0.417,0.25 5.323,0.25 5.74,0.5 0.417,0.25 0.573,2.167 0.99,2.417 0.417,0.25 1.802,2.167 2.219,2.417 0.417,0.25 3.26,2.167 3.677,2.417 0.417,0.25 4.802,2.167 5.219,2.417 0.417,0.25 5.958,2.167 6.375,2.417 0.417,0.25 1.563,0.292 1.99,0.51 0.427,0.219 10 false K3 3.49,0.292 3.917,0.51 0.427,0.219 10 false K2 5.448,0.292 5.875,0.51 0.427,0.219 10 false K1 6.052,2.198 6.479,2.417 0.427,0.219 10 false RA 4.854,2.198 5.281,2.417 0.427,0.219 10 false K135 3.375,2.198 3.802,2.417 0.427,0.219 10 false K4 1.958,2.198 2.385,2.417 0.427,0.219 10 false r2 0.719,2.198 1.146,2.417 0.427,0.219 10 false r3

a.

Measure the resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-28 (V+) - K3-1 (GND1) V - BR Video signal Panoramic image being displayed Pulse generation
(Refer to waveform 1)
K2-29 (V-) - K3-1 (GND1) SB - BR Ground Always Below 1 Ω


b.

Reference (Oscilloscope waveform):

i.
E336160C01
1.115,2.26 1.01,2.833 1.01,2.833 0.896,2.833 false 1.25,2.135 1.406,2.854 1.406,2.854 1.583,2.854 false 0.229,0.313 0.542,0.51 0.313,0.198 10 false *a 0.271,1.594 0.688,1.792 0.417,0.198 10 false GND 1.625,2.771 1.938,2.969 0.313,0.198 10 false *c 0.698,2.74 1.01,2.938 0.313,0.198 10 false *b
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Synchronization Signal
*c Video Waveform


Waveform 1

Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic image being displayed

HINT:

The video waveform changes according to the image sent by the television camera controller.