Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Panoramic View Monitor / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Panoramic View Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RHD/LHD Data Check Status of the RHD/LHD data check Normal/Abnormal Normal: Television camera controller is normal
Abnormal: Television camera controller is abnormal
-
HV/ENG Data Check Status of the HV/ENG data check Normal/Abnormal Normal: Television camera controller is normal
Abnormal: Television camera controller is abnormal
-
2WD/4WD Data Check Status of the 2WD/AWD data check Normal/Abnormal Normal: Television camera controller ECU is normal
Abnormal: Television camera controller is abnormal
-
Main CPU Forced Termination Detection Record A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the engine switch off and a forced end was applied No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Main CPU Abnormal Response Record A history item indicating that the main CPU became unresponsive in normal status No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Main CPU Abnormal Reset Record A history item indicating that the main CPU was reset, although the engine switch was not turned off in normal status No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Image Processing IC Written Protect Record A history item indicating that the image processing IC memory was write protected No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Image Processing IC Initialized Malfunction Record A history item indicating that the image processing IC memory was not initialized No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Main EEPROM Access Status Main EEPROM access status Normal/Abnormal Normal: Television camera controller is normal
Abnormal: Television camera controller is abnormal
-
Sub EEPROM Access Status Sub-EEPROM access status Normal/Abnormal Normal: Television camera controller is normal
Abnormal: Television camera controller is abnormal
-
System Power Supply Voltage Malfunction Record A history item indicating an abnormally generated-voltage value from the system power source No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Main CPU Starting Malfunction Record A history item indicating that the main CPU did not start No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
CAN CPU Boot Malfunction Record A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Wheel Speed Sensor (4wheel) Reception state of the vehicle speed signal from the skid control ECU Valid/Invalid Valid: Speed signal received
Invalid: Speed signal not received
-
Bus-off Continuation Detection Record A history item indicating that the bus off condition was detected No/Yes No: Television camera controller is normal
Yes: Television camera controller is abnormal
-
Shift R Position Reverse signal ON/OFF OFF: Shift lever in any position except R
ON: Shift lever in R
-
Camera Changing SW Signal Status Signal status at the BLSW terminal (switch camera signal) ON/OFF ON: Panoramic view monitor switch on
OFF: Panoramic view monitor switch off
-
Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
NG: Rear television camera assembly or television camera controller is abnormal
-
Side Camera LH Availability Consistency Status of ECU stored in side television camera assembly LH OK/NG OK: Normal
NG: Side television camera assembly LH or television camera controller is abnormal
-
Front Camera Availability Consistency Status of ECU stored in front television camera assembly OK/NG OK: Normal
NG: Front television camera assembly or television camera controller is abnormal
-
Side Camera RH Availability Consistency Status of ECU stored side television camera assembly RH OK/NG OK: Normal
NG: Side television camera assembly RH or television camera controller is abnormal
-
Image Adjustment Status Status of the image adjustment status Incomplete/Processing/Complete Incomplete: Image adjustment incomplete
Processing: Image adjustment in processing
Complete: Image adjustment completed
-
Number of DTC Number of DTCs (past and present) Min: 0, Max: 255 Changes according to the number of DTCs output -
Chassis > Parking Assist Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Video Output Status Output condition of video signal OK or NG OK: Output condition of video signal is normal
NG: Output condition of video signal is abnormal
-
Circumference Monitoring System Type Check Verification of rear television camera assembly signal OK or NG OK: Rear television camera assembly normal
NG: Rear television camera assembly abnormal
-
EEPROM Status (Initial read) Rear television camera assembly information OK or NG OK: Rear television camera assembly normal
NG: Rear television camera assembly abnormal
-
CPU Communication Status Rear television camera assembly information OK or NG OK: Rear television camera assembly normal
NG: Rear television camera assembly abnormal
-
Number of DTC Number of stored DTCs min.: 0, max.: 255 Number of DTCs will be displayed -
Current Key Cycle Cumulative number of times the engine switch was turned on (IG) Min.: 0, Max.: 65535 time Cumulative number of times the engine switch was turned on (IG) will be displayed -
Current Key Cycle Elapsed Time Time elapsed since the engine switch was turned on (IG) Min.: 0, Max.: 1677721.5 s Time elapsed since the engine switch was turned on (IG) will be displayed -