Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the television camera controller. The television camera controller controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E50
5.073,2.844 6.99,3.479 1.917,0.635 10 false Television Camera Controller 5.073,2.688 5.531,2.885 0.458,0.198 10 false R123 5.302,2.135 5.979,2.354 0.677,0.219 10 false GND1 5.313,1.729 5.99,1.948 0.677,0.219 10 false ACC 5.323,1.313 6,1.531 0.677,0.219 10 false IG 5.313,0.885 5.99,1.104 0.677,0.219 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 2 5.115,1.188 5.271,1.385 0.156,0.198 10 false 6 5.104,1.625 5.26,1.823 0.156,0.198 10 false 1 5.115,2.021 5.271,2.219 0.156,0.198 10 false 3 3.229,1.073 4.76,1.271 1.531,0.198 10 false ECU-B NO. 2 3.219,1.5 4.75,1.698 1.531,0.198 10 false ECU-IG1 NO. 3 3.323,1.917 4.115,2.135 0.792,0.219 10 false ECU-ACC 1.396,0.875 4,1.073 2.604,0.198 10 false from Battery 0.844,1.292 3.448,1.49 2.604,0.198 10 false from IG1-NO. 1 Relay 1.177,1.708 3.781,1.906 2.604,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


HINT:

If the television camera controller does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - BODY GROUND)
a.

Disconnect the R123 television camera controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R123-3 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER POWER SOURCE)
a.

Disconnect the R123 television camera controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R123-2 (+B) - R123-3 (GND1) Always 11 to 14 V
R123-1 (ACC) - R123-3 (GND1) Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V
R123-6 (IG) - R123-3 (GND1) Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR