Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351456 REAR CRANKSHAFT OIL SEAL A

6AR-FSE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Remove any old seal packing.


c.
A342966C01
0.688,2.656 1.719,3.115 1.719,3.115 2.719,2.656 true 1.656,3.135 1.969,3.333 0.313,0.198 10 false *a 0.156,2.552 0.354,2.771 0.198,0.219 10 true *b 0.635,2.99 0.844,3.167 0.208,0.177 10 true *b 3.063,2.583 3.271,2.76 0.208,0.177 10 true *b 2.646,2.979 2.854,3.156 0.208,0.177 10 true *b
*a Seal Packing
*b 3.0 mm (0.118 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install a new rear engine oil seal within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




e.
A413607C01
0.802,1.865 0.5,1.646 0.5,1.646 1.031,1.521 true 1.615,2.885 1.781,3.083 0.167,0.198 10 false + 2.604,2.875 2.771,3.073 0.167,0.198 10 false - 2.094,2.75 2.406,2.948 0.313,0.198 10 false *a 0.198,1.563 0.656,1.76 0.458,0.198 10 false SST
*a 0.35 to 0.55 mm


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

0.35 to 0.55 mm (0.0138 to 0.0217 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A413608N01
0.635,1.031 1.542,1.885 1.542,1.885 1.281,1.219 true 1.479,1.906 1.938,2.104 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)



b.

Clean the 8 bolts and bolt holes.


c.
A413609

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A413610C01
1,0.365 2.156,0.365 true 2.438,2.063 2.688,2.063 2.688,2.063 2.917,1.635 true 0.833,0.26 1.146,0.458 0.313,0.198 10 false *1 2.271,1.958 2.583,2.156 0.313,0.198 10 false *2
*1 Drive Plate And Ring Gear Sub-assembly
*2 Rear Drive Plate Spacer


Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

NOTICE:

As the rear drive plate spacer and drive plate and ring gear sub-assembly are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



e.
A192239C77
1.573,0.76 1.677,0.76 1.677,0.76 1.823,1.24 false 1.375,0.677 1.573,0.833 0.198,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A413611N01
1.75,0.323 1.906,0.521 0.156,0.198 10 true 1 1.771,1.656 1.927,1.854 0.156,0.198 10 true 2 1.073,0.969 1.229,1.167 0.156,0.198 10 true 3 2.375,1.01 2.531,1.208 0.156,0.198 10 true 4 1.219,0.594 1.375,0.792 0.156,0.198 10 true 5 2.229,1.479 2.385,1.677 0.156,0.198 10 true 6 2.24,0.604 2.396,0.802 0.156,0.198 10 true 7 1.292,1.49 1.448,1.688 0.156,0.198 10 true 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.