Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER HEAD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351459 CYLINDER HEAD A

6AR-FSE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A194970E04
0.109,0.36 0.404,0.523 0.295,0.163 10 SST 0.957,0.654 0.473,0.446 0.473,0.446 1.087,1.105 false

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194985

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a new intake valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


Standard Bush Length:

41.3 to 41.7 mm (1.63 to 1.64 in.)


If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A337941C03
1.125,1.302 0.427,0.823 0.427,0.823 0.917,0.823 true 2.406,0.333 2.583,0.531 0.177,0.198 10 true *a 0.083,0.75 0.406,0.979 0.323,0.229 10 true SST
*a Protrusion Height


Using SST and a hammer, tap in the selected intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.85 to 15.1 mm (0.585 to 0.594 in.)



g.
A337942

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A337943N01
1.469,1.188 0.875,1.615 0.875,1.615 1.604,0.75 true 0.75,1.635 1.208,1.833 0.458,0.198 10 true SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.
A194975

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select a new exhaust valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


Standard Bush Length:

46.8 to 47.2 mm (1.84 to 1.86 in.)


If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A337944C01
1.469,1.208 0.823,1.698 0.823,1.698 1.615,0.781 true 2.99,1.156 3.219,1.365 0.229,0.208 10 true *a 0.677,1.729 1.021,1.969 0.344,0.24 10 true SST
*a Protrusion Height


Using SST and a hammer, tap in the selected exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

14.25 to 14.5 mm (0.561 to 0.571 in.)



g.
A337945

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11115A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 2 ring pins.


b.
A336671C01
2.26,2.5 2.573,2.656 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)