Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER HEAD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351459 CYLINDER HEAD G

6AR-FSE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and exhaust manifold converter sub-assembly (TWC: Front Catalyst).

A336669C01
4.167,0.219 4.479,0.375 0.313,0.156 10 false *a 4.188,1.833 4.5,1.99 0.313,0.156 10 false *b 4.219,2.917 4.531,3.073 0.313,0.156 10 false *c
*a Cylinder Block Sub-assembly Side *b Intake Manifold Side
*c Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) Side - -


Maximum Warpage:
Item Specified Condition
Cylinder block sub-assembly side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold converter sub-assembly (TWC: Front Catalyst) side 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


b.
A336670

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

If cracks are found, replace the cylinder head sub-assembly.


Hide 13715H 2.INSPECT COMPRESSION SPRING

a.
A342870

Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:

50.78 mm (2.00 in.)


If the free length is not as specified, replace the compression spring.


b.
A342871C01
1.875,0.135 2.188,0.333 0.313,0.198 10 false *a 0.958,1.427 1.271,1.625 0.313,0.198 10 false *b
*a Deviation
*b 36.7 mm (1.44 in.)


Using a steel square, measure the deviation of the compression spring.

Maximum Deviation:

1.28 mm (0.0504 in.)


Maximum Angle:

2°


If the deviation is more than the maximum, replace the compression spring.


Hide 13711 3.INSPECT INTAKE VALVE

a.
A194992

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.


b.
A194993C14
0.539,1.54 1.677,1.715 1.138,0.175 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


c.
A194994C12
2.192,1.055 3.177,1.207 0.985,0.152 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:

103.92 mm (4.09 in.)


Minimum Overall Length:

103.42 mm (4.07 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.
A194995

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.


b.
A194996C16
0.541,1.541 0.76,1.712 0.219,0.171 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.50 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


c.
A194997C12
2.321,0.989 2.612,1.173 0.291,0.184 10 *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:

112.91 mm (4.45 in.)


Minimum Overall Length:

112.41 mm (4.43 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 5.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A194967

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and valve guide bush.


Hide 11131 6.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.
A194998C16
1.692,1.719 2.107,1.889 0.416,0.17 10 *a
*a Width


Lightly press the valve face against the intake valve seat.

HINT:

Do not rotate the intake valve while pressing it.



c.

Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric. If not, replace the intake valve.


ii.

If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric. If not, resurface the intake valve seat.


iii.

Check that the intake valve seat contacts the middle of the valve face with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).



Hide 11135 7.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.
A194999C12
1.508,1.731 1.924,1.897 0.416,0.166 10 *a
*a Width


Lightly press the valve face against the exhaust valve seat.

HINT:

Do not rotate the exhaust valve while pressing it.



c.

Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric. If not, replace the exhaust valve.


ii.

If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric. If not, resurface the exhaust valve seat.


iii.

Check that the exhaust valve seat contacts the middle of the valve face with the width between 1.2 to 1.6 mm (0.0472 to 0.0630 in.).