Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER HEAD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351459 CYLINDER HEAD A

6AR-FSE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

HINT:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A289330C01
2.271,1.396 2.271,1.083 false 2.208,1.406 2.469,1.625 0.26,0.219 10 false *a 1.854,0.26 2.115,0.521 0.26,0.26 10 false *b 1.646,1.74 1.99,2.031 0.344,0.292 10 false *c
*a Adhesive
*b Application Width
*c Distance


Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


Distance:

1.0 to 7.0 mm (0.0394 to 0.276 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Do not expose the spark plug tube to engine oil for at least 1 hour after installing it.




b.
A336672C01
2.615,2.927 2.927,3.083 0.313,0.156 10 false *a
*a Protrusion Height


Using a wooden block and hammer, tap in the 4 spark plug tubes to the specified protrusion height.

Standard Protrusion Height:

112 mm (4.41 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 17159 2.INSTALL CYLINDER HEAD STUD BOLT

a.

Using an E8 and E10 "TORX" socket wrench, install the 9 cylinder head stud bolts.

A336673C01
0.313,0.25 0.625,0.406 0.313,0.156 10 false *a 0.323,1.802 0.635,1.958 0.313,0.156 10 false *b 0.698,3.375 1.01,3.531 0.313,0.156 10 false *c 5.448,0.698 5.76,0.854 0.313,0.156 10 false *d 5.458,1.271 5.771,1.427 0.313,0.156 10 false *e 5.844,0.99 6.156,1.146 0.313,0.156 10 false *f 5.906,2.625 6.219,2.781 0.313,0.156 10 false *g 5.469,4.219 5.781,4.375 0.313,0.156 10 false *h 5.823,4.083 6.135,4.24 0.313,0.156 10 false *i 5.896,2.26 6.208,2.417 0.313,0.156 10 false *d 5.448,3.927 5.76,4.083 0.313,0.156 10 false *g 5.073,0.177 5.229,0.375 0.156,0.198 10 false A 1.302,0.479 1.458,0.677 0.156,0.198 10 true A 2.448,0.458 2.604,0.656 0.156,0.198 10 true A 5.073,1.76 5.229,1.958 0.156,0.198 10 false B 1.146,1.719 1.302,1.917 0.156,0.198 10 false B 2.302,1.729 2.458,1.927 0.156,0.198 10 false B 0.656,3 0.813,3.198 0.156,0.198 10 false B 1.656,2.99 1.813,3.188 0.156,0.198 10 false B 2.646,3.01 2.802,3.208 0.156,0.198 10 false B 5.073,3.49 5.229,3.688 0.156,0.198 10 false C 1.76,3.427 1.917,3.625 0.156,0.198 10 false C 2.229,3.594 2.385,3.792 0.156,0.198 10 true C
*a Intake Manifold Side *b Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) Side
*c Rear Side *d 26 mm (1.02 in.)
*e 16.7 mm (0.657 in.) *f 51.7 mm (2.04 in.)
*g 14 mm (0.551 in.) *h 13 mm (0.512 in.)
*i 29 mm (1.14 in.) - -


Torque:
Stud Bolt (A), (C) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Stud Bolt (B) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A337937

Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11117F 4.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A194961

Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 13734B 5.INSTALL EXHAUST VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head sub-assembly.


Hide 6.INSTALL VALVE STEM OIL SEAL

a.
A329098C05
0.688,0.198 0.927,0.406 0.24,0.208 10 false *a 2.646,0.229 2.906,0.427 0.26,0.198 10 false *b 1.406,0.375 1.646,0.573 0.24,0.198 10 false *c
*a Intake Valve Stem Oil Seal
*b Exhaust Valve Stem Oil Seal
*c "NOK" Mark


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay attention when installing the valve stem oil seals. For example, installing an intake valve stem oil seal onto the exhaust side or installing an exhaust valve stem oil seal onto the intake side can cause installation problems later.



b.
A337946C01
2.646,0.896 2.698,0.26 2.698,0.26 2.906,0.26 true 1.042,2.177 1.354,2.333 0.313,0.156 10 false *a 2.323,2.167 2.635,2.323 0.313,0.156 10 false *b 2.958,0.156 3.333,0.344 0.375,0.188 10 false SST
*a Correct
*b Incorrect


Using SST, push in the valve stem oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the valve stem oil seal to be damaged or improperly seated.



Hide 13711 7.INSTALL INTAKE VALVE

a.
A285332C18
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.

Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A337935N01
1.521,1.115 2.24,1.865 2.24,1.865 1.5,1.865 true 2.302,1.792 2.76,1.99 0.458,0.198 10 true SST

Using SST, compress each compression spring and install the 8 valve spring retainer locks.

SST
09202-70020  09202-00020  


d.
A339211

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.




Hide 13715 8.INSTALL EXHAUST VALVE

a.
A285332C19
2.698,1.563 3.01,1.719 0.313,0.156 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A337936N01
1.667,1.792 0.667,1.802 0.667,1.802 2.021,1.208 true 0.365,1.729 0.823,1.927 0.458,0.198 10 false SST

Using SST, compress each compression spring and install the 8 valve spring retainer locks.

SST
09202-70020  09202-00020  


d.
A339212

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.