Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351460 CYLINDER BLOCK A

6AR-FSE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston or piston ring set.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E8 and E10 "TORX" socket wrenches, install the stud bolts.

A336690C01
0.604,0.198 0.917,0.354 0.313,0.156 10 false *a 0.604,1.604 0.917,1.76 0.313,0.156 10 false *b 2.302,1.146 2.458,1.344 0.156,0.198 10 true A 1.448,1.146 1.604,1.344 0.156,0.198 10 true A 1.823,2.083 1.979,2.281 0.156,0.198 10 true B 3.865,0.104 4.021,0.302 0.156,0.198 10 false A 3.865,1.188 4.021,1.385 0.156,0.198 10 false B 4.646,0.417 4.958,0.573 0.313,0.156 10 false *c 4.667,0.708 4.979,0.865 0.313,0.156 10 false *d 4.896,0.563 5.208,0.719 0.313,0.156 10 false *e 4.677,1.625 4.99,1.781 0.313,0.156 10 false *f 4.677,2.188 4.99,2.344 0.313,0.156 10 false *g 4.917,1.844 5.229,2 0.313,0.156 10 false *h
*a RH Side *b LH Side
*c 20 mm (0.787 in.) *d 13 mm (0.512 in.)
*e 35 mm (1.38 in.) *f 46 mm (1.81 in.)
*g 19 mm (0.748 in.) *h 67 mm (2.64 in.)


Torque:
Stud Bolt (A) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Stud Bolt (B) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A337948

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13211 3.INSTALL PISTON

a.

Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.

HINT:
·

Perform this procedure only when replacement of the piston pin hole snap ring (rear side) is necessary.

·

Tape the screwdriver tip before use.




b.

Gradually heat the piston to 80 to 90°C (176 to 194°F).


c.

Coat the piston, piston pin and connecting rod with engine oil.


d.
A336691C01
1.01,2.99 1.01,2.823 1.01,2.823 1.104,2.615 false 3.042,1.427 3.042,1.146 3.042,1.146 2.573,0.521 false 1.104,1.292 0.719,0.354 0.719,0.354 0.542,0.354 false 0.375,0.26 0.688,0.417 0.313,0.156 10 false *a 0.958,3.01 1.271,3.167 0.313,0.156 10 false *b 3,1.448 3.313,1.604 0.313,0.156 10 false *b
*a Cutout
*b Front Mark


Align the cutout of the piston and front mark of the connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the piston pin hole snap ring.

NOTICE:

Do not change the combination of the pistons and piston pins.



e.
A336692C01
0.531,1.719 1.063,1.719 true 1.531,1.875 2.063,1.875 true 1.896,0.906 2.396,1.698 2.396,1.698 2.563,1.698 true 0.375,1.646 0.688,1.802 0.313,0.156 10 false *1 2.104,1.802 2.417,1.958 0.313,0.156 10 false *a 2.615,1.625 2.927,1.781 0.313,0.156 10 false *b
*1 Piston Pin Hole Snap Ring
*a Cutout
*b Protective Tape


Using a screwdriver, install a new piston pin hole snap ring (front side) on the other side of the piston pin hole.

HINT:
·

Be sure that the end gap of the piston pin hole snap ring is not aligned with the service hole front mark portion of the piston.

·

Tape the screwdriver tip before use.




f.
A336693

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and piston pin as a set.


ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and piston pin as a set.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Hide 13011 4.INSTALL PISTON RING SET

a.
A336694C02
2.635,0.833 2.948,0.833 false 2.635,1.333 2.948,1.333 false 2.531,1.115 2.948,1.115 false 1.333,0.917 1.667,0.219 1.667,0.219 1.896,0.219 false 2.979,0.76 3.292,0.917 0.313,0.156 10 false *1 3,1.042 3.313,1.198 0.313,0.156 10 false *2 3,1.26 3.313,1.417 0.313,0.156 10 false *3 1.938,0.135 2.25,0.292 0.313,0.156 10 false *a
*1 Upper Side Rail
*2 Oil Ring Expander
*3 Lower Side Rail
*a Groove for Oil Ring Expander, Upper Side Rail and Lower Side Rail


Install the oil ring expander, upper side rail and lower side rail by hand.

NOTICE:

Make sure that the oil ring expander ends do not overlap each other.



b.
A336695C02
0.583,2.667 0.885,2.667 0.885,2.667 1.073,2.906 false 0.604,3.271 0.906,3.271 0.906,3.271 1.094,3.51 false 2.042,2.656 2.719,2.656 true 2.031,3.125 2.708,3.125 true 2.01,3.292 2.25,3.5 2.25,3.5 2.719,3.5 false 1.052,4.458 1.052,4.26 false 2.167,4.448 2.167,4.25 false 0.396,2.583 0.708,2.74 0.313,0.156 10 false *1 0.438,3.188 0.75,3.344 0.313,0.156 10 false *2 2.76,3.052 3.073,3.208 0.313,0.156 10 false *a 2.76,3.427 3.073,3.583 0.313,0.156 10 false *b 2.76,2.583 3.073,2.74 0.313,0.156 10 false *b 1,4.469 1.313,4.625 0.313,0.156 10 false *1 2.115,4.479 2.427,4.635 0.313,0.156 10 false *2
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Code Mark
*b Paint Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.

Piston Ring Mark:
Item Code Mark Paint Mark
No. 1 Compression Ring - Yellow
No. 2 Compression Ring A2 Blue


NOTICE:
·

The No. 1 compression ring can be installed with either side facing upward.

·

Install the No. 2 compression ring with the code mark (A2) facing upward.

·

Paint marks can only be checked on new compression rings. When reusing compression rings, check each compression ring profile in order to install them to the correct positions.



HINT:

Perform "Inspection After Repair" after replacing the piston ring set.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



c.
A336696C03
0.917,2.656 1.167,2.656 1.167,2.656 1.479,2.198 false 0.906,1.604 1.219,1.76 0.313,0.156 10 false *1 2.917,1.604 3.229,1.76 0.313,0.156 10 false *2 0.917,1.802 1.229,1.958 0.313,0.156 10 false *3 1.875,0.708 2.188,0.865 0.313,0.156 10 false *4 2.917,1.792 3.229,1.948 0.313,0.156 10 false *5 0.76,2.573 1.073,2.729 0.313,0.156 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Upper Side Rail
*4 Oil Ring Expander
*5 Lower Side Rail
*a Front Mark
V100135

Front Side


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

Regardless of the front mark, the piston rings are positioned correctly if their ends are positioned opposite of each other.



Hide 13471A 5.INSTALL CRANKSHAFT PULLEY KEY

a.

Install the 2 crankshaft pulley keys to the crankshaft.


Hide 11711 6.INSTALL CRANKSHAFT BEARING

a.
A195816C12
1.614,3.832 1.787,3.984 0.173,0.151 10 *a 2.638,3.832 2.812,3.991 0.173,0.159 10 *b
*a Correct
*b Incorrect


Clean the main journal and both surfaces of the crankshaft bearings and No. 2 crankshaft bearings.


b.

Install the crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the crankshaft bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the crankshaft bearing inner surface.

·

If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.




c.
A195817C14
2.333,3.219 1.948,2.573 1.948,2.573 1.802,2.573 false 0.552,3.729 0.76,3.958 0.208,0.229 10 false A 2.219,3.708 2.427,3.938 0.208,0.229 10 false B 1.604,2.49 1.771,2.635 0.167,0.146 10 false *a
*a Vernier Caliper


Install the No. 2 crankshaft bearings onto the crankshaft bearing caps.


d.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the No. 2 crankshaft bearing edge.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the No. 2 crankshaft bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the No. 2 crankshaft bearing inner surface.

·

If any coolant comes into contact with the No. 2 crankshaft bearing inner surface, replace the No. 2 crankshaft bearing with a new one.




Hide 11791 7.INSTALL CRANKSHAFT THRUST WASHER

a.
A337947C01
1.74,1.375 0.698,0.292 0.698,0.292 1.313,1.25 true 0.563,0.135 0.875,0.333 0.313,0.198 10 false *a
*a Oil Groove


Apply engine oil to the crankshaft thrust washers.


b.

Install the 2 crankshaft thrust washers onto the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 8.INSTALL CRANKSHAFT

a.
A338968C01
1.823,2.781 2.313,2.781 false 2.354,2.708 2.667,2.865 0.313,0.156 10 false *a
*a Front Mark


Apply engine oil to the crankshaft bearings, and place the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the No. 2 crankshaft bearings.


c.

Confirm the front marks and numbers, and install the 5 crankshaft bearing caps onto the cylinder block sub-assembly with the front marks as shown in the illustration.

HINT:

The crankshaft bearing cap bolts are tightened in 3 progressive steps.



d.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.


e.

Step 1:

i.
A338969N01
0.438,0.604 0.594,0.802 0.156,0.198 10 false 7 0.438,1.573 0.594,1.771 0.156,0.198 10 false 8 1.052,1.708 1.208,1.906 0.156,0.198 10 true 4 1.833,1.771 1.99,1.969 0.156,0.198 10 true 2 2.635,1.677 2.802,1.875 0.167,0.198 10 true 6 3.135,1.698 3.365,1.896 0.229,0.198 10 true 10 0.948,0.5 1.073,0.677 0.125,0.177 10 true 3 1.833,0.406 1.958,0.583 0.125,0.177 10 true 1 2.667,0.615 2.792,0.792 0.125,0.177 10 true 5 3.219,0.552 3.344,0.729 0.125,0.177 10 false 9

Uniformly install and tighten the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



f.

Step 2:

i.

Tighten the 10 crankshaft bearing cap bolts again in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

If a crankshaft bearing cap bolt cannot be tightened to the specified torque, replace it.



g.

Step 3:

i.
A132155C09
2.25,0.138 2.406,0.285 0.156,0.148 10 *a 1.998,0.722 2.226,0.226 false 1.003,0.404 1.381,0.602 0.378,0.198 10 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the crankshaft bearing cap bolts with paint.


ii.

Tighten the crankshaft bearing cap bolts by 90° in the order shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



h.

Check that the crankshaft turns smoothly.


Hide 13041 9.INSTALL CONNECTING ROD BEARING

a.
A195818C13
0.406,3.073 0.521,3.073 0.521,3.073 0.74,3.448 false 1.729,3.667 1.938,3.896 0.208,0.229 10 false A 2.854,3.656 3.063,3.885 0.208,0.229 10 false B 0.24,2.979 0.417,3.135 0.177,0.156 10 false *a
*a Vernier Caliper


Clean the connecting rod bearing contact surface of the connecting rod and connecting rod cap, and both surfaces of both connecting rod bearings.


b.

Install the connecting rod bearings to the connecting rods and connecting rod caps.


c.

Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the edges of the connecting rod cap and connecting rod bearing.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the connecting rod bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the connecting rod bearing inner surface.

·

If any coolant comes into contact with the connecting rod bearing inner surface, replace the connecting rod bearing with a new one.




Hide 10.INSTALL PISTON WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.
A336696C03
0.917,2.656 1.167,2.656 1.167,2.656 1.479,2.198 false 0.906,1.604 1.219,1.76 0.313,0.156 10 false *1 2.917,1.604 3.229,1.76 0.313,0.156 10 false *2 0.917,1.802 1.229,1.958 0.313,0.156 10 false *3 1.875,0.708 2.188,0.865 0.313,0.156 10 false *4 2.917,1.792 3.229,1.948 0.313,0.156 10 false *5 0.76,2.573 1.073,2.729 0.313,0.156 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Upper Side Rail
*4 Oil Ring Expander
*5 Lower Side Rail
*a Front Mark
V100135

Front Side


Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

Regardless of the front mark, the piston rings are positioned correctly if their ends are positioned opposite of each other.



c.
A336697C01
1.458,1.104 1.688,1.396 1.688,1.396 1.958,1.396 false 2,1.323 2.313,1.479 0.313,0.156 10 false *a
*a Front Mark


Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing the engine front.

NOTICE:

When inserting the piston with connecting rod into the cylinder block sub-assembly, make sure the No. 1 oil nozzle sub-assembly does not interfere with the connecting rod.



d.
A338773C01
0.406,0.385 0.656,0.385 0.656,0.385 1.115,0.844 true 0.229,0.302 0.542,0.5 0.313,0.198 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.

NOTICE:

Match the connecting rod cap with the connecting rod.



e.
A338771

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Install the 8 connecting rod bolts.

NOTICE:

The connecting rod bolts are tightened in 2 progressive steps.



g.

Step 1:

i.

Alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.
A101478C51
2.063,0.729 2.375,0.531 false 1.083,0.323 1.438,0.5 0.354,0.177 10 false 90° 2.417,0.375 2.625,0.552 0.208,0.177 10 false *a
*a Paint Mark
V100136

Engine Front


Step 2:

i.

Mark the front of the connecting rod bolts with paint.


ii.

Tighten the connecting rod bolts by 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.