Home › Engine / Hybrid System › 6AR-FSE (STARTING) › STARTER › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072209 6AR-FSE STARTING _0351490 STARTER A

6AR-FSE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PLANETARY GEAR

a.
A344486C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and repair service starter kit.


b.

Install the 3 planetary gears to the repair service starter kit.


Hide 2.INSTALL RUBBER SEAL

a.

Install the rubber seal to the repair service starter kit.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A347623

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.



Hide 28140 4.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A215977

Hold the brush spring back and set the 4 brushes as shown in the illustration.


b.
A215968

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes as shown in the illustration.


c.
A314282C03
1.396,0.219 1.552,0.219 1.552,0.219 2.458,0.771 true 2.51,0.563 2.938,0.156 2.938,0.156 3.073,0.156 true 2.167,1.542 2.302,1.542 2.302,1.542 2.51,0.958 true 1.208,0.104 1.521,0.26 0.313,0.156 10 false *a 3.146,0.063 3.375,0.219 0.229,0.156 10 false *b 1.99,1.438 2.302,1.594 0.313,0.156 10 false *c
*a Grommet
*b Negative (-) Brush Holder Plate
*c Positive (+) Motor Lead Wire


Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.


Hide 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A209964C03
1.885,0.24 2.052,0.24 2.052,0.24 2.219,0.396 false 1.25,2.01 1.51,2.01 1.51,2.01 2.031,1.208 true 0.469,1.813 0.635,1.813 0.635,1.813 1.198,0.885 true 0.281,1.719 0.594,1.875 0.313,0.156 10 false *a 1.083,1.906 1.396,2.104 0.313,0.198 10 false *b 1.729,0.125 2.042,0.281 0.313,0.156 10 false *a
*a Lead Wire Rubber
*b Cutout


Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

Align the lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.



b.
A187214

Install the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 6.INSTALL STARTER ARMATURE PLATE

a.
A426485C01
2.708,1.5 3.042,1.5 false 2.542,1 2.708,0.667 2.708,0.667 2.938,0.667 false 1.74,0.833 1.906,0.5 1.906,0.5 2.135,0.5 true 1.531,1.667 1.531,1.167 true 1.104,1.604 1.104,1.104 false 1.042,1.604 1.354,1.76 0.313,0.156 10 false *1 2.969,0.573 3.281,0.729 0.313,0.156 10 false *2 1.479,1.667 1.792,1.823 0.313,0.156 10 false *a 3.083,1.406 3.396,1.563 0.313,0.156 10 false *b 2.167,0.406 2.479,0.563 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Armature Plate
*a Stopper
*b Protrusion


Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

NOTICE:

Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A207175C06
1.813,1.5 1.948,1.833 1.948,1.833 2.135,1.833 false 2.583,1.333 2.719,1.844 2.719,1.844 2.906,1.844 false 2.188,1.74 2.427,1.969 0.24,0.229 10 false *a 2.948,1.74 3.219,1.958 0.271,0.219 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.


b.
A187222

Using a T25 "TORX" socket wrench, install the starter yoke assembly with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A344423C02
1.698,0.51 2.073,0.26 2.073,0.26 2.177,0.26 true 2.333,0.521 2.625,0.271 2.625,0.271 2.75,0.271 false 1.313,0.49 0.906,0.198 0.906,0.198 0.667,0.198 true 2.76,0.188 3.073,0.344 0.313,0.156 10 false *1 0.51,0.094 0.74,0.292 0.229,0.198 10 false *a 2.188,0.167 2.5,0.323 0.313,0.156 10 false *b
*1 Magnet Starter Switch Assembly
*a Pinion Drive Lever
*b Hook
V100135

High-temperature Grease


Apply high-temperature grease to the plunger as shown in the illustration.


b.

Hang the hook of the magnet starter switch assembly on the pinion drive lever.


c.
A201461

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
A187220

Connect the field coil lead wire to the magnet starter switch assembly with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)