Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM U

6AR-FSE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A424791N01
2.24,0.458 2.635,0.688 0.396,0.229 5.781,0.458 6.177,0.688 0.396,0.229 2.302,0.49 2.76,0.688 0.458,0.198 10 false C58 5.854,0.49 6.313,0.688 0.458,0.198 10 false A78

HINT:

The standard voltage, resistance and waveform between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A78-1 (BATT) - C58-53 (E1) R - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A78-2 (+B) - C58-53 (E1) L - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
A78-3 (+B2) - C58-53 (E1) L - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
A78-6 (IGSW) - C58-53 (E1) B - W-B Engine switch signal Engine switch on (IG) 11 to 14 V
A78-8 (IREL) - C58-53 (E1) P - W-B D INJ relay operation signal Engine switch on (IG) Below 1.5 V
A78-9 (STP) - C58-53 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A78-10 (ST1-) - C58-53 (E1) LG - W-B Stop light switch assembly signal (opposite to STP terminal) Engine switch on (IG), brake pedal depressed Below 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
A78-13 (CANH) - C58-53 (E1) B - W-B CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 1)
A78-14 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A78-21 (FPC) - C58-53 (E1) R - W-B Fuel pump control Engine switch on (IG) Below 1.5 V
A78-26 (CANL) - C58-53 (E1) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 2)
A78-29 (STA) - C58-53 (E1) G - W-B Starter assembly signal Cranking 6.0 V or higher
A78-30 (NEO) - C58-53 (E1) B - W-B Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(see waveform 3)
A78-31 (TACH) - C58-53 (E1) P - W-B Engine speed signal Idling with warm engine Pulse generation
(see waveform 4)
A78-33 (TC) - C58-53 (E1) GR - W-B Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
A78-44 (SPD) - C58-53 (E1) L - W-B Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(see waveform 5)
A78-46 (MREL) - C58-53 (E1) W - W-B EFI-MAIN NO. 1 relay operation signal Engine switch on (IG) 11 to 14 V
A78-47 (VPA) - A78-48 (EPA) G - L Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 2.6 to 4.5 V
A78-49 (VCPA) - A78-48 (EPA) BE - L Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A78-50 (VPA2) - A78-51 (EPA2) GR - P Accelerator pedal position sensor signal Engine switch on (IG), accelerator pedal fully released 1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 4.75 V
A78-52 (VCP2) - A78-51 (EPA2) SB - P Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
A78-57 (NSW) - C58-53 (E1) BE - W-B Park/Neutral position switch assembly signal Engine switch on (IG) and shift lever not in P or N 11 to 14 V
Engine switch on (IG) and shift lever in P or N Below 3.0 V
A78-58 (KSW) - C58-53 (E1) R - W-B Electrical key in vehicle signal Electrical key outside vehicle 11 to 14 V
A78-59 (S) - C58-53 (E1) GR - W-B S shift position signal Engine switch on (IG), shift lever in S 11 to 14 V
Engine switch on (IG), shift lever not in S Below 1.5 V
A78-60 (RFC) - C58-53 (E1) LG - W-B Cooling fan control signal Engine switch on (IG), A/C switch on (max cool) Pulse generation
(See waveform 6)
C58-9 (OC1+) - C58-8 (OC1-) LG - BE Cam timing oil control solenoid assembly operation signal Idling Pulse generation
(See waveform 7)
C58-16 (M+) - C58-49 (ME01) B - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 8)
C58-17 (HT1B) - C58-53 (E1) L - W-B Heated oxygen sensor heater operation signal Engine switch on (IG) 11 to 14 V
Idling with cold engine Below 3.0 V
C58-18 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C58-19 (HA1A) - C58-18 (E04) R - W-B Air fuel ratio sensor heater operation signal Engine switch on (IG) 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 9)
C58-21 (#2D+) - C58-20 (#2D-) W - B No. 2 direct fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 10)
C58-22 (#3D+) - C58-23 (#3D-) P - V No. 3 direct fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 10)
C58-25 (#4D+) - C58-24 (#4D-) Y - L No. 4 direct fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 10)
C58-26 (#1D+) - C58-27 (#1D-) BR - G No. 1 direct fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 10)
C58-28 (FP1+) - C58-53 (E1) W - W-B Fuel pump with seal assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C58-29 (FP1-) - C58-53 (E1) B - W-B Fuel pump with seal assembly (for high pressure side) signal Idling with warm engine, Data List item "Injection Mode" displaying "Direct" Pulse generation
(See waveform 11)
C58-30 (+BD1) - C58-53 (E1) W - W-B Power source of ECU (injector driver) Engine switch on (IG) 11 to 14 V
C58-32 (EGR4) - C58-53 (E1) V - W-B EGR valve assembly EGR valve operating Pulse generation
(See waveform 12)
C58-33 (EGR2) - C58-53 (E1) GR - W-B EGR valve assembly EGR valve operating Pulse generation
(See waveform 12)
C58-34 (D) - C58-53 (E1) R - W-B D shift position signal Engine switch on (IG), shift lever in D or S 11 to 14 V
Engine switch on (IG), shift lever not in D or S Below 1 V
C58-35 (R) - C58-53 (E1) W - W-B R shift position signal Engine switch on (IG), shift lever in R 11 to 14 V
Engine switch on (IG), shift lever not in R Below 1 V
C58-36 (EGR1) - C58-53 (E1) BE - W-B EGR valve assembly EGR valve operating Pulse generation
(See waveform 12)
C58-37 (EGR3) - C58-53 (E1) L - W-B EGR valve assembly EGR valve operating Pulse generation
(See waveform 12)
C58-38 (OE1+) - C58-68 (OE1-) R - V Camshaft timing oil control valve assembly operation signal Idling Pulse generation
(see waveform 13)
C58-39 (IGT4) - C58-53 (E1) B - W-B No. 4 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C58-40 (IGT3) - C58-53 (E1) P - W-B No. 3 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C58-41 (IGT2) - C58-53 (E1) R - W-B No. 2 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C58-42 (IGT1) - C58-53 (E1) W - W-B No. 1 ignition coil assembly (ignition signal) Idling with warm engine Pulse generation
(see waveform 14)
C58-46 (M-) - C58-49 (ME01) W - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(see waveform 15)
C58-47 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C58-48 (+BM) - C58-53 (E1) G - W-B Power source of throttle actuator Always 11 to 14 V
C58-49 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C58-50 (E02) - Body ground W-B - - Ground Always Below 1 Ω
C58-51 (E01) - Body ground W-B - - Ground Always Below 1 Ω
C58-53 (E1) - Body ground W-B - - Ground Always Below 1 Ω
C58-54 (#20) - C58-53 (E1) G - W-B No. 2 port fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(see waveform 16)
C58-55 (#30) - C58-53 (E1) LG - W-B No. 3 port fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(see waveform 16)
C58-56 (#40) - C58-53 (E1) BE - W-B No. 4 port fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(see waveform 16)
C58-57 (#10) - C58-53 (E1) B - W-B No. 1 port fuel injector assembly signal Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(see waveform 16)
C58-58 (E1D2) - Body ground W-B - - Ground Always Below 1 Ω
C58-59 (E1D1) - Body ground W-B - - Ground Always Below 1 Ω
C58-60 (+BD2) - C58-53 (E1) B - W-B D INJ relay signal Engine switch on (IG) 11 to 14 V
C58-64 (P) - C58-53 (E1) B - W-B P shift position signal Engine switch on (IG), shift lever in P 11 to 14 V
Engine switch on (IG), shift lever not in P Below 1 V
C58-65 (N) - C58-53 (E1) LG - W-B N shift position signal Engine switch on (IG), shift lever in N 11 to 14 V
Engine switch on (IG), shift lever not in N Below 1 V
C58-70 (PRG) - C58-53 (E1) W - W-B Purge VSV operation signal Engine switch on (IG) 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(see waveform 17)
C58-76 (NE+) - C58-109 (NE-) L - R Crank position sensor signal Idling with warm engine Pulse generation
(see waveform 18)
C58-81 (EV1+) - C58-112 (EV1-) LG - W Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(see waveform 19)
C58-82 (VV1+) - C58-114 (VV1-) B - R Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(see waveform 19)
C58-88 (VTA2) - C58-120 (ETA) W - G Throttle position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
C58-90 (VCVG) - C58-91 (E2G) LG - B Power source of mass air flow meter sub-assembly Engine switch on (IG) 4.8 to 5.2 V
C58-92 (VG) - C58-91 (E2G) BE - B Mass air flow meter sub-assembly signal Engine switch on (IG) Pulse generation
(See waveform 20)
C58-94 (THA) - C58-91 (E2G) G - B Intake air temperature sensor signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C58-97 (THEO) - C58-96 (ETHE) LG - BE Engine oil temperature sensor signal Idling with warm engine 0 to 5.0 V
C58-98 (PEO) - C58-129 (EPEO) G - W Oil pressure sender gauge assembly signal Idling with warm engine 0.5 to 4.5 V
C58-99 (OX1B) - C58-100 (EX1B) B - W Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 21)
C58-101 (IGF1) - C58-53 (E1) G - W-B Ignition coil assembly (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 14)
C58-103 (PR) - C58-135 (EPR) P - G Fuel pressure sensor (fuel delivery pipe sub-assembly) signal Idling with warm engine 0.5 to 4.5 V
C58-104 (THW) - C58-105 (ETHW) B - W Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C58-106 (PIM) - C58-137 (EPIM) P - G Manifold absolute pressure sensor signal Engine switch on (IG) 3.0 to 4.5 V
C58-110 (VCNE) - C58-53 (E1) V - W-B Power source of crank position sensor Engine switch on (IG) 4.5 to 5.5 V
C58-111 (VCE1) - C58-53 (E1) B - W-B Power source of camshaft position sensor (for exhaust camshaft) Engine switch on (IG) 4.5 to 5.5 V
C58-113 (VCV1) - C58-53 (E1) W - W-B Power source of camshaft position sensor (for intake camshaft) Engine switch on (IG) 4.5 to 5.5 V
C58-121 (VCTA) - C58-120 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C58-122 (VTA1) - C58-120 (ETA) B - G Throttle position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
C58-124 (KNK1) - C58-123 (EKNK) B - W Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 22)
C58-130 (VCPE) - C58-129 (EPEO) V - W Power source of engine oil sender gauge assembly Engine switch on (IG) 4.75 to 5.25 V
C58-131 (A1A+) - C58-53 (E1) L - W-B Air fuel ratio sensor signal Engine switch on (IG) 3.0 to 3.6 V*
C58-132 (A1A-) - C58-53 (E1) P - W-B Air fuel ratio sensor signal Engine switch on (IG) 2.7 to 3.3 V*
C58-136 (VCPR) - C58-135 (EPR) B - G Power source of fuel pressure sensor (fuel delivery pipe sub-assembly) (for high pressure side) signal Engine switch on (IG) 4.75 to 5.25 V
C58-138 (VCPM) - C58-137 (EPIM) B - G Power source of manifold absolute pressure sensor Engine switch on (IG) 4.75 to 5.25 V

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


WAVEFORM 1


A292386E01
1.365,1.917 2.104,2.094 0.74,0.177 10 10 μs./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A292387E02
3,1.375 3.344,1.573 0.344,0.198 10 GND 2.781,0.26 3.385,0.469 0.604,0.208 10 1 V/DIV. 1.385,1.885 2.156,2.052 0.771,0.167 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A287796E02
2.594,1.656 3.052,1.854 0.458,0.198 10 GND 0.063,0.063 0.781,0.292 0.719,0.229 10 1 V/DIV. 1.167,1.927 2,2.135 0.833,0.208 10 2 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A287797E02
2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.656,0.156 3.302,0.396 0.646,0.24 10 false 5 V/DIV. 2.625,1.844 3.427,2.063 0.802,0.219 10 false 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A292384E04
2.813,1.25 3.271,1.448 0.458,0.198 10 false GND 1.146,2.01 1.917,2.167 0.771,0.156 10 false 20 ms./DIV. 2.708,0.135 3.313,0.313 0.604,0.177 10 false 2 V/DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A282867E08
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Engine switch on (IG), A/C switch on (max cool)


WAVEFORM 7


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 8


A208000E03
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A205412E06
2.646,0.042 3.25,0.229 0.604,0.188 10 5 V/DIV. 2.698,0.906 3.063,1.073 0.365,0.167 10 GND 1.156,1.865 1.917,2.042 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 10


A405747E01
0.302,0.573 0.76,0.771 0.458,0.198 10 false CH1 0.313,0.938 0.771,1.135 0.458,0.198 10 false CH2 1.208,1.896 2.031,2.146 0.823,0.25 10 false 200 μs./DIV. 2.667,0.094 3.354,0.5 0.688,0.406 10 false 50 V/DIV. 2.781,0.594 3.24,0.792 0.458,0.198 10 false GND 2.771,0.948 3.229,1.146 0.458,0.198 10 false GND

No. 1 (to No. 4) Direct Fuel Injector Assembly Signal
ECM Terminal Name CH1: Between #1D+ and E1
CH2: Between #1D- and E1
CH1: Between #2D+ and E1
CH2: Between #2D- and E1
CH1: Between #3D+ and E1
CH2: Between #3D- and E1
CH1: Between #4D+ and E1
CH2: Between #4D- and E1
Tester Range 50 V/DIV., 200 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 11


A405748E05
2.771,0.094 3.406,0.438 0.635,0.344 10 false 20 V/DIV. 1.26,1.885 2.573,2.177 1.313,0.292 10 false 500 μs./DIV. 0.26,0.406 1.573,0.698 1.313,0.292 10 false CH1 0.26,1.083 1.573,1.375 1.313,0.292 10 false CH2 2.76,0.438 3.135,0.865 0.375,0.427 10 false GND 2.76,1.104 3.135,1.531 0.375,0.427 10 false GND

Fuel Pump with Seal Assembly (for High Pressure Side) Signal
ECM Terminal Name CH1: Between FP1+ and E1
CH2: Between FP1- and E1
Tester Range 20 V/DIV., 500 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 12


A214026E01
2.849,2.294 3.179,2.450 0.330,0.156 10 GND 2.849,1.922 3.179,2.077 0.330,0.156 10 GND 2.849,1.578 3.179,1.734 0.330,0.156 10 GND 2.849,1.24 3.179,1.396 0.330,0.156 10 GND 0.235,1.039 0.686,1.195 0.451,0.156 10 EGR1 0.235,1.405 0.686,1.560 0.451,0.156 10 EGR2 0.235,1.757 0.686,1.913 0.451,0.156 10 EGR3 0.235,2.113 0.686,2.269 0.451,0.156 10 EGR4 1.248,2.42 1.997,2.577 0.749,0.157 10 50 ms./DIV. 1.979,0.406 2.643,0.581 0.665,0.175 10 20 V/DIV.

EGR Valve Assembly Signal
ECM Terminal Name Between EGR1 and E1
Between EGR2 and E1
Between EGR3 and E1
Between EGR4 and E1
Tester Range 20 V/DIV., 50 ms./DIV.
Condition EGR valve operating


WAVEFORM 13


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 14


A289263E01
2.844,0.857 3.210,1.059 0.366,0.202 10 GND 2.844,1.502 3.175,1.704 0.331,0.202 10 GND 0.058,0.41 0.435,0.915 0.376,0.504 10 CH1 (IGT) 0.021,1.193 0.440,1.551 0.419,0.358 10 CH2 (IGF1) 0.03,0.036 0.574,0.213 0.545,0.177 10 2 V/DIV. 1.154,1.844 1.905,1.988 0.751,0.145 10 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A245848E01
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 16


A292383E01
0.667,1.583 1.125,1.781 0.458,0.198 10 GND 1.865,1.906 2.75,2.104 0.885,0.198 10 20 ms./DIV. 0.531,0.177 1.417,0.375 0.885,0.198 10 20 V/DIV.

No. 1 (to No. 4) Port Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E1
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Port"

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.




WAVEFORM 17


A218020E09
2.667,0.177 3.365,0.448 0.698,0.271 10 10 V/DIV. 2.802,0.948 3.26,1.292 0.458,0.344 10 GND 1.188,1.792 2,2 0.813,0.208 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 18


A200774E09
2.688,0.052 3.385,0.271 0.698,0.219 10 false 2 V/DIV. 1.271,1.896 2.5,2.094 1.229,0.198 10 false 20 ms./DIV. 2.969,1.188 3.427,1.427 0.458,0.24 10 false GND

Crank Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A255508E16
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.646 0.427,0.813 0.323,0.167 10 CH1 0.125,1.469 0.448,1.635 0.323,0.167 10 CH2 0.052,0.813 0.427,1.01 0.375,0.198 10 (VV1) 0.063,1.625 0.458,1.813 0.396,0.188 10 (EV1) 3.042,0.823 3.365,1.021 0.323,0.198 10 GND 3.031,1.594 3.375,1.854 0.344,0.26 10 GND 1.302,1.896 2.052,2.073 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor (for Intake and Exhaust Camshaft) Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 20


A337204E01
0.156,1.417 0.615,1.615 0.458,0.198 10 false GND 1.333,1.969 2.281,2.167 0.948,0.198 10 false 100 μs./DIV. 2.76,0.073 3.406,0.333 0.646,0.26 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Engine switch on (IG)


WAVEFORM 21


A292382E01
0.615,1.469 1.073,1.667 0.458,0.198 10 GND 0.479,0.177 1.469,0.365 0.99,0.188 10 0.2 V/DIV. 1.854,1.906 2.844,2.094 0.99,0.188 10 200 ms./DIV.

Heated Oxygen Sensor (Sensor 2) Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the item O2 Sensor Voltage B1S2 shows the values input to the ECM from the heated oxygen sensor.



WAVEFORM 22


A283572E06
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.