Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P010511  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground  


DESCRIPTION

A263608E28
0.094,2.302 0.531,2.531 0.438,0.229 10 false 1.0 0.094,2.156 0.708,2.406 0.615,0.25 10 false 1.2 0.094,1.708 0.5,1.969 0.406,0.26 10 false 2.4 0.094,1.26 0.552,1.51 0.458,0.25 10 false 3.6 0.094,0.99 0.51,1.271 0.417,0.281 10 false 4.2 0.958,3.615 1.219,3.781 0.26,0.167 10 false 2.9 1.521,3.438 1.906,3.625 0.385,0.188 10 false 8.699 2.042,3.438 2.563,3.635 0.521,0.198 10 false 14.499 0.667,3.427 1.188,3.667 0.521,0.24 10 false 1.933 2.531,3.438 2.99,3.677 0.458,0.24 10 false 17.399 0.125,0.469 0.927,0.667 0.802,0.198 10 false Voltage (V) 0.625,4.01 2.906,4.26 2.281,0.25 10 false Intake Manifold Absolute Pressure 2.948,3.583 3.281,3.813 0.333,0.229 10 false psi 2.906,2.979 3.26,3.156 0.354,0.177 10 false kPa 0.802,3.052 1.25,3.208 0.448,0.156 10 false 19.998 0.531,2.792 0.979,2.948 0.448,0.156 10 false 13.332 1.427,2.802 1.875,2.958 0.448,0.156 10 false 59.995 2.01,3.052 2.458,3.208 0.448,0.156 10 false 99.992 2.354,2.802 2.906,2.958 0.552,0.156 10 false 119.990 0.104,0.083 3.427,0.49 3.323,0.406 10 false Characteristics of Manifold Absolute Pressure Sensor:

The manifold absolute pressure sensor detects the intake manifold pressure as a change in voltage. The ECM calculates the intake manifold pressure based on this voltage. The ECM calculates the EGR valve assembly and purge VSV opening amount according to changes in the intake manifold pressure and also detects errors in the manifold absolute pressure sensor using these changes in pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010511 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground The manifold absolute pressure sensor output voltage is less than 0.5 V for 0.5 seconds or more (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored SAE Code:
P0107

HINT:

When this DTC is output, check the intake manifold absolute pressure in the Data List. Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

DTC No. Intake Manifold Absolute Pressure Malfunction
P010511 Approximately 0 kPa (0 psi)
·

Short to ground in PIM circuit

·

Short in PIM to EPIM circuit

·

Open in VCPM circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


MONITOR DESCRIPTION

The ECM monitors the manifold absolute pressure sensor voltage and uses this value to calculate the intake manifold pressure. When the absolute pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor circuit and stores this DTC.

Example:

If the manifold absolute pressure sensor output voltage is less than 0.5 V for 0.5 seconds or more, the ECM store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Wait 5 seconds or more.

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010511.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A382203E03
1.469,0.917 2,1.313 0.531,0.396 10 false VC 1.417,1.604 1.948,2 0.531,0.396 10 false PIM 1.49,2.375 2.021,2.771 0.531,0.396 10 false E2 0.271,2.729 0.802,3.125 0.531,0.396 10 false C106 0.271,2.896 2.719,3.177 2.448,0.281 10 false Manifold Absolute Pressure Sensor 1.771,0.802 2.302,1.198 0.531,0.396 10 false 3 1.771,1.479 2.302,1.875 0.531,0.396 10 false 2 1.771,2.281 2.302,2.677 0.531,0.396 10 false 1 4.313,0.802 4.844,1.198 0.531,0.396 10 false 138 4.333,1.49 4.865,1.885 0.531,0.396 10 false 106 4.333,2.271 4.865,2.667 0.531,0.396 10 false 137 5.042,3 5.573,3.396 0.531,0.396 10 false C58 5.427,3 5.906,3.281 0.479,0.281 10 false ECM 5.667,0.552 6.198,0.948 0.531,0.396 10 false 5 V 4.667,0.802 5.198,1.198 0.531,0.396 10 false VCPM 4.667,1.49 5.198,1.885 0.531,0.396 10 false PIM 4.667,2.271 5.198,2.667 0.531,0.396 10 false EPIM 5.323,1.313 5.854,1.708 0.531,0.396 10 false 180 kΩ

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376493C09
0.417,1.063 0.833,1.313 0.417,0.25 0.927,1.729 1.396,1.26 true 1.458,1.885 1.708,1.292 true 2.479,1.854 2,1.281 true 0.458,1.094 0.896,1.385 0.438,0.292 10 false C106 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.802,1.76 1.115,1.958 0.313,0.198 10 false E2 1.313,1.927 1.771,2.125 0.458,0.198 10 false PIM 2.438,1.896 2.75,2.094 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C106-3 (VC) - C106-1 (E2) Engine switch on (IG) 4.75 to 5.25 V
C106-2 (PIM) - C106-1 (E2) Engine switch on (IG) 3.0 to 5.25 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C106-3 (VC) - C106-2 (PIM) Engine switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C106-3 (VC) - C58-138 (VCPM) Always Below 1 Ω
C106-2 (PIM) or C58-106 (PIM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR