Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P033511  Crankshaft Position Sensor "A" Circuit Short to Ground  P033515  Crankshaft Position Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

The crank position sensor system consists of a crankshaft position sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crank position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground The crank position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crank position sensor circuit

·

Crank position sensor

·

ECM


Comes on DTC stored SAE Code:
P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open The crank position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crank position sensor circuit

·

Crank position sensor

·

ECM


Comes on DTC stored SAE Code:
P0338

A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If the output voltage transmitted by the crank position sensor remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Crank position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG).

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P033511 or P033515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A415232E02
1.01,2.115 1.448,2.344 0.438,0.229 10 false C104 1,2.271 3.094,2.646 2.094,0.375 10 false Crank Position Sensor 5.063,2.24 5.5,2.469 0.438,0.229 10 false C58 5.427,2.24 5.865,2.469 0.438,0.229 10 false ECM 4.833,0.99 5.271,1.219 0.438,0.229 10 false NE+ 4.854,0.448 5.292,0.677 0.438,0.229 10 false VCNE 5.604,0.24 6.042,0.469 0.438,0.229 10 false 5 V 5.49,0.833 6.01,1.031 0.521,0.198 10 false 1.5 kΩ 4.49,0.448 4.927,0.677 0.438,0.229 10 false 110 4.563,0.979 5,1.208 0.438,0.229 10 false 76 4.49,1.521 4.927,1.75 0.438,0.229 10 false 109 2.292,0.438 2.729,0.667 0.438,0.229 10 false 1 2.292,0.99 2.729,1.219 0.438,0.229 10 false 3 2.302,1.542 2.74,1.771 0.438,0.229 10 false 2 1.99,0.448 2.427,0.677 0.438,0.229 10 false VC 4.833,1.531 5.271,1.76 0.438,0.229 10 false NE- 1.917,0.99 2.354,1.219 0.438,0.229 10 false NE+ 1.948,1.531 2.385,1.76 0.438,0.229 10 false NE-

CAUTION / NOTICE / HINT

HINT:
·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

(e)

Start the engine.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crank position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crank position sensor output voltage is insufficient.


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the crank position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR
A424806C01
0.177,1 0.594,1.24 0.417,0.24 0.917,1.917 1.438,1.167 true 2.5,1.917 1.917,1.167 true 1.667,1.917 1.667,1.167 true 0.219,1.031 0.833,1.229 0.615,0.198 10 false C104 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.771,1.917 1.083,2.115 0.313,0.198 10 false VC 1.563,1.927 2.021,2.125 0.458,0.198 10 false NE- 2.458,1.927 2.917,2.125 0.458,0.198 10 false NE+
*a Front view of wire harness connector
(to Crank Position Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the crank position sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C104-1 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C104-3 (NE+) - Body ground Engine switch on (IG) 3.0 to 5.0 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C104-1 (VC) - C104-3 (NE+) Engine switch off 1.425 to 1.575 kΩ
C104-2 (NE-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANK POSITION SENSOR - ECM)
a.

Disconnect the crank position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C104-1 (VC) - C58-110 (VCNE) Always Below 1 Ω
C104-3 (NE+) - C58-76 (NE+) Always Below 1 Ω
C104-2 (NE-) - C58-109 (NE-) Always Below 1 Ω
C104-1 (VC) or C58-110 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
C104-3 (NE+) or C58-76 (NE+) - Body ground and other terminals Always 10 kΩ or higher
C104-2 (NE-) or C58-109 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR