Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › THROTTLE BODY › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351512 THROTTLE BODY A

6AR-FSE ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during the throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE BATTERY

Hide 17705 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A413315

Slide the clip and disconnect the ventilation hose from the cylinder head cover sub-assembly.


b.

Disengage the clamp to disconnect the ventilation hose from the engine wire.


c.
A413313

Disconnect the mass air flow meter sub-assembly connector.


d.

Disengage the 2 wire harness clamps.


e.
A413318

Disengage the clamp to separate the union to check valve hose from the air cleaner hose assembly.


f.
A413319

Disengage the 2 clamps to separate the No. 2 fuel vapor feed hose assembly from the air cleaner hose assembly.


g.
A425629

Disengage the clamp to separate the heater hose from the air cleaner hose assembly.


h.
A413317

Disengage the clamp to separate the No. 1 fuel hose sub-assembly from the fuel hose bracket.


i.
A413314C01
2.344,2.74 2.625,2.958 0.281,0.219 10 true *a 1.563,0.802 1.76,1 0.198,0.198 10 true *b 2.51,0.792 2.708,0.99 0.198,0.198 10 true *b 1.042,2.99 1.323,3.208 0.281,0.219 10 true *a
*a Air Cleaner Cap Clamp
*b Guide


Disengage the 2 air cleaner cap clamps.


j.

Disengage the 2 guides to separate the air cleaner cap with air cleaner hose from the air cleaner case sub-assembly.


k.
A413321

Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the throttle body with motor assembly.


Hide 22030 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A413323C01
1.615,1.219 1.938,1.219 true 1.156,1.51 1.156,1.875 true 1.969,1.135 2.198,1.375 0.229,0.24 10 true *1 1.104,1.896 1.333,2.083 0.229,0.188 10 true *2
*1 No. 2 Water By-pass Hose
*2 No. 3 Water By-pass Hose


Slide the 2 clips and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the throttle body with motor assembly.


b.

Disconnect the throttle body with motor assembly connector.


c.
A413325

Remove the 4 bolts and throttle body with motor assembly from the intake manifold.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



Hide 22271 7.REMOVE THROTTLE BODY GASKET

a.
A413326

Remove the throttle body gasket from the intake manifold.