Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › RELAY › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351524 RELAY G

6AR-FSE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89561F 1.INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 1)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 electronic fuel injection main relay (EFI-MAIN NO. 1).


Hide 89561G 2.INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 2)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 electronic fuel injection main relay (EFI-MAIN NO. 2).


Hide 89561H 3.INSPECT NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 3)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 3 electronic fuel injection main relay (EFI-MAIN NO. 3).


Hide 85910E 4.INSPECT INJECTOR RELAY (D INJ)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the injector relay (D INJ).


Hide 28371C 5.INSPECT NO. 2 IGNITION RELAY (IG2 NO. 1)

a.
A273391N01
2.667,0.74 2.927,0.74 true 2.531,1.125 2.948,1.125 true 2.531,1.625 2.948,1.625 true 1.708,0.74 1.969,0.74 true 0.229,1.313 0.385,1.51 0.156,0.198 10 1 1.188,1.313 1.344,1.51 0.156,0.198 10 2 0.219,0.781 0.375,0.979 0.156,0.198 10 3 1.188,0.771 1.344,0.969 0.156,0.198 10 5 3,1.052 3.156,1.25 0.156,0.198 10 5 1.604,0.667 1.76,0.865 0.156,0.198 10 1 2.99,0.667 3.146,0.865 0.156,0.198 10 2 3,1.552 3.156,1.75 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 ignition relay (IG2 NO. 1).