Home › Power Source / Network › 6AR-FSE (BATTERY / CHARGING) › GENERATOR › 2018.04–2021.02
RM33A0E _57 Power Source / Network _072212 6AR-FSE BATTERY / CHARGING _0351554 GENERATOR A

6AR-FSE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27415 1.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator assembly in a vise between aluminum plates.


b.
A298990C03
0.667,1.938 0.854,1.938 0.854,1.938 0.958,1.469 false 1.76,0.188 1.99,0.188 1.99,0.188 2.24,0.573 true 3.073,1.563 3.073,0.927 true 2.104,1.677 1.917,1.677 1.917,1.677 1.677,1 false 2.885,1.604 3.344,1.833 0.458,0.229 10 false SST A 0.229,1.844 0.896,2.042 0.667,0.198 10 false SST B 2.177,1.594 2.698,1.792 0.521,0.198 10 false SST A 1.594,0.083 1.906,0.281 0.313,0.198 10 false *a
*a Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


c.
A197239C08
2.229,0.823 2.719,0.823 false 1.948,0.563 2.115,0.25 2.115,0.25 2.24,0.25 false 2.281,0.167 2.802,0.365 0.521,0.198 10 false SST B 2.771,0.75 3.302,0.948 0.531,0.198 10 false SST A 0.896,1.188 1.094,1.438 0.198,0.25 10 true *a 1.813,1.792 2.063,2.01 0.25,0.219 10 false *b
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator assembly is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




d.

Remove SST (A) and (B) from the generator pulley with clutch.


e.

Remove the generator pulley with clutch from the rotor shaft.


f.

Remove the generator assembly from the vise.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A298992

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


c.
A192780

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370A 3.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 4.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A192783N02
1.573,0.771 1.021,0.396 1.021,0.396 0.896,0.396 false 0.531,0.323 0.833,0.5 0.302,0.177 10 false SST

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


c.
A401900

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 5.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A297782

Remove the generator rotor assembly from the generator drive end frame.


Hide 27310B 6.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 27310B 7.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A192788N02
1.542,1.323 0.885,1.323 0.885,1.323 0.885,1.156 false 1.563,1.156 0.479,1.156 false 0.198,1.083 0.51,1.271 0.313,0.188 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)