Home › Vehicle Interior › HEATING / AIR CONDITIONING › RELAY › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0328177 RELAY G

HEATING / AIR CONDITIONING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85934 1.INSPECT MG CLT RELAY

E374255N01
1.396,1.76 1.25,1.76 1.25,1.76 1.052,1.281 true 1.333,0.448 1.208,0.448 1.208,0.448 1.042,0.896 true 0.438,0.469 0.573,0.469 0.573,0.469 0.708,0.927 true 0.219,1.74 0.375,1.74 0.375,1.74 0.49,1.208 true 1.365,0.354 1.552,0.552 0.188,0.198 10 false 1 1.427,1.667 1.729,1.885 0.302,0.219 10 false 2 1.823,0.75 2.021,0.948 0.198,0.198 10 false 3 3.135,0.75 3.313,0.938 0.177,0.188 10 false 5 1.813,1.406 2.125,1.604 0.313,0.198 10 false 1 3.135,1.406 3.385,1.604 0.25,0.198 10 false 2 0.333,0.365 0.521,0.563 0.188,0.198 10 false 5 0.135,1.646 0.333,1.844 0.198,0.198 10 false 3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the MG CLT relay.



Hide 87346K 2.INSPECT PTC HTR RELAY

E218162N26
0.813,0.844 0.938,0.49 0.938,0.49 1.052,0.49 false 1.094,1.135 1.417,0.802 1.417,0.802 1.51,0.802 false 0.813,1.552 0.896,1.771 0.896,1.771 1.01,1.771 false 0.531,1.135 0.385,0.74 0.385,0.74 0.302,0.74 false 1.073,1.677 1.24,1.823 0.167,0.146 10 false 3 1.813,0.75 1.906,0.896 0.094,0.146 10 false 3 0.219,0.635 0.313,0.781 0.094,0.146 10 false 1 1.813,1.24 1.906,1.385 0.094,0.146 10 false 2 1.542,0.698 1.635,0.844 0.094,0.146 10 false 2 3.135,1.229 3.229,1.375 0.094,0.146 10 false 1 1.094,0.385 1.188,0.531 0.094,0.146 10 false 5 3.135,0.75 3.229,0.896 0.094,0.146 10 false 5

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the PTC HTR relay.