CHECK FRONT SEAT HEATER
Turn the engine switch on (IG).
Turn the refreshing seat switch on and check that the indicator illuminates and the surface of the front seat warms up.
Check that the front seat surface temperature changes according to the operation of the refreshing seat switch as follows: HI → MID → LO.
CHECK REAR SEAT HEATER (w/ Rear Seat Heater)
Turn the engine switch on (IG).
Turn the seat heater switch (cooler control switch assembly)*1 or rear seat heater switch*2 on and check that the indicator illuminates and the surface of the rear seat warms up.
*1: for Reclining Type with Rear Seat Heater
*2: for Folding Type with Rear Seat Heater
CHECK THERMOSTAT IN REAR SEAT CUSHION HEATER ASSEMBLY (LH) (for Reclining Type with Rear Seat Heater)
Remove the rear seat cushion heater assembly (LH).
Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER (for Reclining Seat Type)>REMOVAL
Remove the rear seatback heater assembly LH.
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for Reclining Seat Type)>REMOVAL
| *a | Component without harness connected
(Rear Seatback Heater Assembly LH) |
| *b | Component without harness connected
(Rear Seat Cushion Heater Assembly (LH)) |
Connect the C rear seatback heater assembly LH connector and D rear seat cushion heater assembly (LH) connector.
Apply battery voltage and check the operation of the rear seat heater as shown in the table below.
To prevent the rear seat heater from overheating, be sure to disconnect the battery from the rear seat heater immediately after this inspection is completed.
| Battery Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal R102-1 | Rear seat heater temperature 39 to 42°C (102 to 108°F) |
| Battery negative (-) → Terminal R102-2 |
CHECK THERMOSTAT IN REAR SEAT CUSHION HEATER ASSEMBLY (RH) (for Reclining Type with Rear Seat Heater)
Remove the rear seat cushion heater assembly (RH) and rear seat cushion heater assembly (LH).
Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER (for Reclining Seat Type)>REMOVAL
Remove the rear seatback heater assembly RH and rear seatback heater assembly LH.
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for Reclining Seat Type)>REMOVAL
Connect the C rear seatback heater assembly LH connector and D rear seat cushion heater assembly (LH) connector.
Connect the rear seatback heater assembly RH connector and G rear seat cushion heater assembly (RH) connector.
Connect the E rear seat cushion heater assembly (LH) connector and F rear seat cushion heater assembly (RH) connector.
| *a | Component without harness connected
(Rear Seatback Heater Assembly LH) |
*b | Component without harness connected
(Rear Seat Cushion Heater Assembly (LH)) |
| *c | Component without harness connected
(Rear Seat Cushion Heater Assembly (RH)) |
*d | Component without harness connected
(Rear Seatback Heater Assembly RH) |
Apply battery voltage and check the operation of the rear seat heater as shown in the table below.
To prevent the rear seat heater from overheating, be sure to disconnect the battery from the rear seat heater immediately after this inspection is completed.
| Battery Connection | Specified Condition |
|---|---|
| Battery positive (+) → Terminal R102-3 | Rear seat heater temperature 39 to 42°C (102 to 108°F) |
| Battery negative (-) → Terminal R102-4 |
CHECK THERMOSTAT IN REAR SEAT CUSHION HEATER ASSEMBLY (LH) (for Folding Type with Rear Seat Heater)
Remove the rear seat cushion heater assembly (LH).
Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER (for Fold Down Seat Type)>REMOVAL
Remove the rear seatback heater assembly LH.
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for Fold Down Seat Type)>REMOVAL
| *a | Component without harness connected
(Rear Seat Cushion Heater Assembly (LH)) |
| *b | Component without harness connected
(Rear Seatback Heater Assembly LH) |
Connect the I rear seatback heater assembly LH connector and H rear seat cushion heater assembly (LH) connector.
Apply battery voltage and check the operation of the rear seat heater as shown in the table below.
To prevent the rear seat heater from overheating, be sure to disconnect the battery from the rear seat heater immediately after this inspection is completed.
| Battery Connection | Specified Condition |
|---|---|
| Battery negative (+) → Terminal R102-3 | Rear seat heater temperature 39 to 42°C (102 to 108°F) |
| Battery positive (-) → Terminal R102-4 |
CHECK THERMOSTAT IN REAR SEAT CUSHION HEATER ASSEMBLY (RH) (for Folding Type with Rear Seat Heater)
Remove the rear seat cushion heater assembly (RH) and rear seat cushion heater assembly (LH).
Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER (for Fold Down Seat Type)>REMOVAL
Remove the rear seatback heater assembly RH
Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER (for Fold Down Seat Type)>REMOVAL
Connect the L rear seat cushion heater assembly (LH) connector and M rear seat cushion heater assembly (RH) connector.
Connect the J rear seat cushion heater assembly (RH) connector and K rear seatback heater assembly RH connector.
| *a | Component without harness connected
(Rear Seat Cushion Heater Assembly (LH)) |
*b | Component without harness connected
(Rear Seat Cushion Heater Assembly (RH)) |
| *c | Component without harness connected
(Rear seatback Heater Assembly RH) |
- | - |
Apply battery voltage and check the operation of the rear seat heater as shown in the table below.
To prevent the rear seat heater from overheating, be sure to disconnect the battery from the rear seat heater immediately after this inspection is completed.
| Battery Connection | Specified Condition |
|---|---|
| Battery negative (+) → Terminal R102-1 | Rear seat heater temperature 39 to 42°C (102 to 108°F) |
| Battery positive (-) → Terminal R102-2 |