Home › Engine / Hybrid System › 6AR-FSE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072206 6AR-FSE INTAKE / EXHAUST _0353756 EXHAUST MANIFOLD A

6AR-FSE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold converter sub-assembly (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 53851M 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 57533B 4.REMOVE FRONT CENTER FLOOR BRACE

Hide 57523A 5.REMOVE CENTER FLOOR CROSSMEMBER BRACE

Hide 52239B 6.REMOVE BODY MOUNTING PLATE

Hide 17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A413919

Disconnect the heated oxygen sensor connector.


b.
A407105

Remove the 4 bolts, 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and center exhaust pipe assembly.


c.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


d.

Remove the 2 gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 27020 8.REMOVE GENERATOR ASSEMBLY

Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A413920

Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 25611 11.REMOVE EGR PIPE CONNECTOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A413921C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, nut and EGR pipe connector from the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly.


b.
A338734

Remove the 2 EGR cooler gaskets from the EGR pipe connector.


Hide 17118 12.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A413922

Remove the bolt, nut and manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.


Hide 17139 13.REMOVE NO. 2 MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A413923

Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.


Hide 25051 14.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A413924

Remove the 5 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the cylinder head sub-assembly.


b.
A413925

Remove the exhaust manifold gasket from the cylinder head sub-assembly.


Hide 25586 15.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR

a.
A413926

Remove the 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 17168 16.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A413927

Remove the 2 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 17.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A413928

Using an E8 "TORX" socket wrench, remove the stud bolt from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).