Home › Engine / Hybrid System › 6AR-FSE (INTAKE / EXHAUST) › EXHAUST PIPE › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072206 6AR-FSE INTAKE / EXHAUST _0353757 EXHAUST PIPE A

6AR-FSE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A310336C02
0.865,0.219 1.073,0.219 1.073,0.219 1.156,0.594 false 0.75,1.156 0.938,1.156 0.938,1.156 1.094,0.885 false 2.688,0.146 2.469,0.146 2.469,0.146 2.406,0.771 true 0.677,0.156 0.99,0.313 0.313,0.156 10 false *1 0.573,1.083 0.885,1.24 0.313,0.156 10 false *2 2.75,0.073 3.063,0.229 0.313,0.156 10 false *3 0.271,0.688 0.583,0.844 0.313,0.156 10 false *a
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 52239B 3.INSTALL BODY MOUNTING PLATE

a.

Install the body mounting plate with the 6 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 57523A 4.INSTALL CENTER FLOOR CROSSMEMBER BRACE

a.

Install the center floor crossmember brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 57533B 5.INSTALL FRONT CENTER FLOOR BRACE

a.

Install the front center floor brace to the vehicle body with the 4 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 17420 6.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the center exhaust pipe assembly to the exhaust pipe support.


e.

Install the center exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C37
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Center Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and center exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 17430 7.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the center exhaust pipe assembly.


b.

Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly with 2 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 8.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION