This DTC is stored when the blind spot monitor sensor LH detects a short to +B in the outer rear view mirror indicator LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB1 | Short to +B in Outer Mirror Indicator(Slave) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time |
·
Outer mirror LH ·
Outer rear view mirror assembly with cover LH ·
Wire harness or connector ·
Blind spot monitor sensor LH |
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Turn the engine switch off.
Turn the engine switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the W6 blind spot monitor sensor LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND2 outer mirror LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O21*1 or O22*2 outer rear view mirror assembly with cover LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
*1: w/o Panoramic View Monitor System
*2: w/ Panoramic View Monitor System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Turn the engine switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the W6 blind spot monitor sensor LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND2 outer mirror LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O16 outer rear view mirror assembly with cover LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-4 (OMIL) - Body ground | Engine Switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG