Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING › 2018.04–2021.02
RM33A0E _59 Vehicle Exterior _065397 EXTERIOR PANELS / TRIM _0319669 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
·

Front door glass sub-assembly

·

Front door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75720 1.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67856B 2.REMOVE FRONT DOOR PANEL PROTECTOR

Hide 68151C 3.REMOVE FRONT DOOR GLASS RUN

Hide 67862 4.DISCONNECT FRONT DOOR WEATHERSTRIP

a.
B469802

Disengage the 2 clips and disconnect the front door weatherstrip.


Hide 75756C 5.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body or front door rear window frame moulding excessively.


a.

Using a heat light, heat the front door rear window frame moulding.


b.
B469804C01
1.135,1.573 1.552,1.573 true 1.875,1.667 2.292,1.667 true 1.698,1.469 2.219,1.354 true 0.948,1.469 1.167,1.677 0.219,0.208 10 true *a 2.229,1.24 2.448,1.448 0.219,0.208 10 true *b 2.302,1.552 2.521,1.76 0.219,0.208 10 true *a
*a Double-sided Tape
*b Caulking Sponge


Using a moulding remover, disengage the clip and separate the double-sided tape and caulking sponge to remove the front door rear window frame moulding.


Hide 75754A 6.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 7 rivets.

B469806C01
3.667,2 4.052,1.927 false 6.844,1.552 6.729,1.104 false 3.448,1.896 3.76,2.094 0.313,0.198 10 false *a 6.802,1.563 7.115,1.76 0.313,0.198 10 false *b
*a Clamp *b Guide


CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Disengage the clamp and guide to remove the front door upper window frame moulding from the door frame.