Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › 2018.04–2019.10
RM33A0E _52 Drivetrain _065351 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0319440 OIL COOLER A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UA80E Initialization
(Click here)for UA80E Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 28800 1.REMOVE BATTERY

Hide 74404A 3.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 4.REMOVE FRONT WHEEL LH

Hide 53852K 5.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53737B 8.REMOVE FRONT FENDER APRON SEAL LH

Hide 9.DRAIN ENGINE COOLANT

Hide 32942 11.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C370862

Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.



Hide 32941 12.DISCONNECT INLET NO. 1 OIL COOLER HOSE

a.
C374462

Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.



Hide 32907C 13.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

a.
C374463

Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.


b.
C370860

Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.



c.
C370861

Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.



d.
C374464C01
2.802,1.26 2.802,0.885 false 1.646,0.667 1.646,0.302 1.646,0.302 1.771,0.302 false 2.625,0.635 2.625,0.104 2.625,0.104 2.75,0.104 false 1.802,1.771 2.094,1.771 false 0.427,1.854 0.427,1.573 false 1.823,0.198 2.146,0.427 0.323,0.229 10 false *1 2.125,1.656 2.521,1.865 0.396,0.208 10 false *2 2.781,0 3.104,0.219 0.323,0.219 10 false *3 0.365,1.885 0.698,2.094 0.333,0.208 10 false *4 2.74,1.313 3.104,1.583 0.365,0.271 10 false *5
*1 No. 1 Oil Cooler Tube Sub-assembly without Hose
*2 Inlet No. 1 Oil Cooler Hose
*3 Inlet No. 2 Oil Cooler Hose
*4 Outlet No. 1 Oil Cooler Hose
*5 Outlet No. 2 Oil Cooler Hose


Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.


Hide 16261G 14.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
C374465

Disengage the 3 clamps to remove the transmission breather clamp.


b.
C374466

Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.



Hide 16260 15.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C374467

Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.



Hide 33493A 16.REMOVE TRANSMISSION OIL COOLER

a.
C370868

Remove the 3 bolts.


b.

Disengage the hook to remove the transmission oil cooler from the automatic transaxle case sub-assembly.

HINT:

Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.