Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319414 FUEL INJECTOR(for Port Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17190 4.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 5.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A405956

Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23800 6.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.
A405957C01
0.406,0.208 0.583,0.375 0.177,0.167 10 true *a 1.552,0.073 1.74,0.229 0.188,0.156 10 true *b 2.385,1.208 2.573,1.365 0.188,0.156 10 true *b
*a Fuel Pressure Sensor Connector
*b No. 5 Engine Wire Connector


Disconnect the fuel pressure sensor connector.


b.

Disconnect the 2 No. 5 engine wire connectors.


c.
A368852

Remove the 4 bolts and fuel delivery pipe with sensor assembly with the 6 fuel injector assemblies from the intake manifold.

NOTICE:
·

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.

·

When removing the fuel delivery pipe with sensor assembly, hold the pipe by both ends and pull it straight upward.




Hide 23807V 7.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A405958

Remove the 4 No. 1 delivery pipe spacers from the intake manifold.


Hide 23291 8.REMOVE INJECTOR VIBRATION INSULATOR

a.
A405959

Remove the 6 injector vibration insulators from the intake manifold.


Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

a.

for Bank 2:

i.
A368855

Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


ii.

Pull the 3 fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


iii.
A368856

Disconnect the 3 fuel injector assembly connectors.



b.

for Bank 1:

i.
A368857

Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


ii.

Pull the 3 fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


iii.
A368858

Disconnect the 3 fuel injector assembly connectors.



c.

Remove the O-ring from each fuel injector assembly.


d.
A361004N01
2.042,0.365 2.604,0.604 0.563,0.24 10 true No. 1

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.