Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL MAIN VALVE › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319424 FUEL MAIN VALVE A

2GR-FKS FUEL  FUEL MAIN VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 83320 2.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 23070 4.REMOVE FUEL MAIN VALVE ASSEMBLY

a.
A405975

Remove the fuel main valve assembly (for Low Pressure).

i.

Remove the clip from the fuel filter.


ii.
A405976C01
1.448,0.76 1.646,0.229 1.646,0.229 1.802,0.229 true 1.833,0.146 2.042,0.323 0.208,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.



b.
A405977

Remove the fuel main valve assembly (for High Pressure).

i.

Remove the clip from the fuel filter.


ii.
A405978C01
2.031,0.979 2.156,0.573 2.156,0.573 2.26,0.573 true 2.313,0.5 2.625,0.656 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.