The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during horn button assembly removal/installation are shown below.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 6AR-FSE: Click hereGeneral>MAINTENANCE>6AR-FSE BATTERY>REMOVAL
for 2AR-FE: Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>REMOVAL
for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
45186
3.REMOVE LOWER NO. 2 STEERING WHEEL COVER
Using a screwdriver with its tip wrapped with protective tape, disengage each claw to remove the 3 lower No. 2 steering wheel covers.
Be careful when disengaging the claws, as the lower No. 2 steering wheel cover may fly off.
| *A | for LH Side | *B | for RH Side |
| *C | for Under Side | - | - |
| *a | Protective Tape | - | - |
45130
4.REMOVE HORN BUTTON ASSEMBLY
|
Deployment Side |
When storing the horn button assembly, keep the airbag deployment side facing upward.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| *a | Torsion Spring |
|
Push in this Direction |
Using a screwdriver, push in the 3 torsion springs to disengage the 3 pins as shown in the illustration.
Lightly hold the horn button assembly so that it does not fall.
Insert the screwdriver from the installation holes for the 3 lower No. 2 steering wheel covers.
Pull out the horn button assembly from the steering wheel assembly and hold the horn button assembly with one hand.
When separating the horn button assembly, do not pull the airbag wire harness.
| *a | Airbag Connector |
| *b | Horn Connector |
| *c | Airbag Connector Locking Button |
| *d | Protective Tape |
| *e | Wire Harness Clamp |
|
Release in this Direction |
|
Remove in this Direction |
w/o Occupant Classification System:
Disconnect the horn connector from the horn button assembly.
Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Using a screwdriver with its tip wrapped with protective tape, release the lock and remove the wire harness clamp to remove the horn button assembly.
| *a | Airbag Connector |
| *b | Horn Connector |
| *c | Airbag Connector Locking Button |
| *d | Protective Tape |
| *e | Wire Harness Clamp |
|
Release in this Direction |
|
Remove in this Direction |
w/ Occupant Classification System:
Disconnect the horn connector from the horn button assembly.
Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons.
Disconnect the 2 airbag connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Using a screwdriver with its tip wrapped with protective tape, release the lock and remove the wire harness clamp to remove the horn button assembly.