Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327345 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62180A 3.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:
B417759C02
0,0 0,0 false
V100155

Deployment Side


When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B489943C01
0.917,0.635 1.177,0.333 1.177,0.333 1.375,0.333 true 1.677,2.219 1.938,1.917 1.938,1.917 2.135,1.917 true 0.948,1.917 1.198,1.917 1.198,1.917 1.51,2.354 true 2.146,1.823 2.396,2.042 0.25,0.219 10 true *a 1.406,0.26 1.719,0.417 0.313,0.156 10 false *b 0.76,1.813 0.948,2.031 0.188,0.219 10 true *c
*a Airbag Connector
*b Airbag Connector Locking Button
*c Protective Tape
V113147

Release in this Direction


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

Using needle nose pliers, remove the 4 pins from the 4 clips (A).

NOTICE:

Do not damage the pins.


B489944C01
1.969,1.885 2.25,1.885 true 3.427,1.917 3.646,1.917 true 4.354,2.365 4.563,2.365 4.563,2.365 4.729,2.167 true 6.115,1.01 6.115,0.615 6.115,0.615 6.333,0.615 true 2.281,1.823 2.5,2.031 0.219,0.208 10 false *1 1.25,1.5 1.563,1.656 0.313,0.156 10 false *a 0.271,0.625 0.448,0.802 0.177,0.177 10 true *b 3.677,1.854 3.896,2.063 0.219,0.208 10 false *1 1.542,0.375 1.729,0.563 0.188,0.188 10 true *b 3.573,0.833 3.76,1 0.188,0.167 10 true *b 4.521,0.313 4.708,0.479 0.188,0.167 10 true *b 5.542,0.542 5.729,0.708 0.188,0.167 10 true *b 4.198,2.292 4.396,2.49 0.198,0.198 10 false *2 6.354,0.521 6.573,0.729 0.219,0.208 10 true *c
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Spacer Location - -
V113147

Remove in this Direction - -



e.

Using 2 screwdrivers, disengage the 2 claws of each clip (A), and separate the 4 clips (A) from the vehicle body as shown in the illustration.

HINT:

Separate the 4 clips (A) and curtain shield airbag assembly from the vehicle body as a unit.



f.

Disengage the 5 clips (B).


g.

While holding the curtain shield airbag assembly, remove the 4 bolts and curtain shield airbag assembly.


h.

Remove the 4 clips (A) and a spacer from the curtain shield airbag assembly.