The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.
1. PRECAUTION
As the standard wheel alignment values differ depending on the suspension type, refer to the following table to confirm the suspension type for each model.
| MODEL CODE | SUSPENSION TYPE |
|---|---|
| ASV70R-AETDKQ | NORMAL |
| ASV70R-AETNKQ | NORMAL |
| ASV70R-AETVKQ | SPORT |
| GSV70R-AEZNBQ | NORMAL |
| GSV70R-AEZVBQ | SPORT |
| AXVA70L-AEZDBV | NORMAL |
| AXVA70L-AEZNBV | NORMAL |
| AXVA70L-AEZSBV | SPORT |
| ASV70L-AETDKV | NORMAL |
| ASV70L-AETNKV | NORMAL |
| ASV70L-AETSKV | SPORT |
| GSV70L-AEZGBV | NORMAL |
| GSV70L-AEZSBV | SPORT |
| ASV70L-AETNKW | NORMAL |
| AXVA70L-AEZNBW | NORMAL |
| GSV70L-AEZGBW | NORMAL |
| ASV70R-AETNKW | NORMAL |
| ASV71L-RETNHX | NORMAL |
| ASV70L-RETNKX | NORMAL |
| GSV70L-REZGBX | NORMAL |
| ASV70L-AETDKR | NORMAL |
2.INSPECT TIRES
3.MEASURE VEHICLE HEIGHT
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
A: Ground clearance of front wheel center
B: Ground clearance of center of bolt head of front lower No. 2 suspension arm bushing (rear bolt of front lower No. 1 suspension arm sub-assembly).
C: Ground clearance of rear wheel center
D: Ground clearance of center of bolt head of rear No. 2 suspension arm assembly and rear suspension member sub-assembly.
| Engine | SUSPENSION TYPE | Front A - B | Rear C - D |
|---|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
|||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | 150 mm (5.91 in.)
138 mm (5.43 in.)* |
49 mm (1.93 in.)
38 mm (1.50 in.)* |
| SPORT | 150 mm (5.91 in.) | 46 mm (1.81 in.) | |
| 2GR-FKS | NORMAL | 155 mm (6.10 in.)
140 mm (5.51 in.)* |
53 mm (2.09 in.)
41 mm (1.61 in.)* |
| SPORT | 152 mm (5.98 in.) | 49 mm (1.93 in.) | |
4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
Inspect while the vehicle is unloaded.
| *a | Turning Radius Gauge |
| *b | Camber-caster-kingpin Gauge |
Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
Inspect the camber, caster and steering axis inclination.
| Engine | SUSPENSION TYPE | Camber Inclination | Right-left Difference |
|---|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
|||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | -0°30' +/- 0°45' (-0.50° +/- 0.75°)
-0°20' +/- 0°45' (-0.33° +/- 0.75°)* |
0°45' (0.75°) or less |
| SPORT | -0°30' +/- 0°45' (-0.50° +/- 0.75°) | ||
| 2GR-FKS | NORMAL | -0°35' +/- 0°45' (-0.58° +/- 0.75°)
-0°25' +/- 0°45' (-0.42° +/- 0.75°)* |
|
| SPORT | -0°30' +/- 0°45' (-0.50° +/- 0.75°) | ||
| Engine | SUSPENSION TYPE | Caster Inclination | Right-left Difference |
|---|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
|||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)* |
0°45' (0.75°) or less |
| SPORT | 5°20' +/- 0°45' (5.33° +/- 0.75°) | ||
| 2GR-FKS | NORMAL | 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)* |
|
| SPORT | 5°20' +/- 0°45' (5.33° +/- 0.75°) | ||
| Engine | SUSPENSION TYPE | Steering Axis Inclination Reference |
|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | 12°55' (12.92°)
12°35' (12.58°)* |
| SPORT | 12°55' (12.92°) | |
| 2GR-FKS | NORMAL | 13°00' (13.00°)
12°40' (12.67°)* |
| SPORT | 13°00' (13.00°) | |
5.ADJUST CAMBER
Inspect toe-in after the camber has been adjusted.
Remove the front wheel.
Remove the 2 nuts on the lower side of the front shock absorber assembly.
Keep the bolts inserted.
Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.
Reinstall each bolt after removing it and confirming steering knuckle movement.
If the steering knuckle does not move freely in the front shock absorber assembly, clean the contact surfaces of the front shock absorber assembly and the steering knuckle.
Temporarily install the 2 nuts. (Step A)
Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)
Tighten the 2 nuts.
Keep the bolts from rotating when tightening the nuts.
Install the front wheel.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Check the camber.
| Engine | SUSPENSION TYPE | Camber Inclination | Right-left Difference |
|---|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
|||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | -0°30' +/- 0°45' (-0.50° +/- 0.75°)
-0°20' +/- 0°45' (-0.33° +/- 0.75°)* |
0°45' (0.75°) or less |
| SPORT | -0°30' +/- 0°45' (-0.50° +/- 0.75°) | ||
| 2GR-FKS | NORMAL | -0°35' +/- 0°45' (-0.58° +/- 0.75°)
-0°25' +/- 0°45' (-0.42° +/- 0.75°)* |
|
| SPORT | -0°30' +/- 0°45' (-0.50° +/- 0.75°) | ||
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center of the specified range - measured value
Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.
Try to adjust the camber to the center of the specified values.
| To move the axle hub toward (+) in step B | To move the axle hub toward (-) in step B |
|---|---|
| Refer to table (1) (To move the axle hub toward the positive side) | Refer to table (2) (To move the axle hub toward the negative side) |
The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.
Replace the nut with a new one when replacing the bolt.
Table (1) (To move the axle hub toward the positive side)
| *A | Table (1) (To move the axle hub toward the positive side) | *B | Selected Bolt Combination |
| *a | Installed Bolt | *b | Adjusting Value |
| *c | Standard Bolt | *d | 90105-17013 |
| *e | 90105-17014 | *f | 90105-17015 |
Table (2) (To move the axle hub toward the negative side)
| *A | Table (2) (To move the axle hub toward the negative side) | *B | Selected Bolt Combination |
| *a | Installed Bolt | *b | Adjusting Value |
| *c | Standard Bolt | *d | 90105-17013 |
| *e | 90105-17014 | *f | 90105-17015 |
If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.
Replace one bolt at a time when replacing both bolts.
6.INSPECT TOE-IN
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| Engine | SUSPENSION TYPE | Specified Condition |
|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)* |
| B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)* |
||
| SPORT | C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°) | |
| B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.) | ||
| 2GR-FKS | NORMAL | C + D: 0°06' +/- 0°10' (0.09° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)* |
| B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)* |
||
| SPORT | C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°) | |
| B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.) | ||
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the steering rack ends.
7.ADJUST TOE-IN
| *a | Thread Length |
Make sure that the thread length of the right and left steering rack ends are approximately the same.
1.5 mm (0.0591 in.) or less
Separate the steering rack boot clips from the steering rack boot.
Loosen the tie rod assembly lock nuts.
Adjust the steering rack ends if the difference in thread length between the right and left steering rack ends is not within the specified range.
If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the difference in length is within the specified range.
If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the difference in length is within the specified range.
Measure the toe-in.
|
Front of the Vehicle |
Turn the right and left steering rack ends by an equal amount to adjust the toe-in.
Perform adjustments so that the value is as close as possible to the median of the specified range.
| Engine | SUSPENSION TYPE | Specified Condition |
|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)* |
| B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)* |
||
| SPORT | C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°) | |
| B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.) | ||
| 2GR-FKS | NORMAL | C + D: 0°06' +/- 0°10' (0.09° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)* |
| B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)* |
||
| SPORT | C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°) | |
| B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.) | ||
Make sure that the thread length of the right and left steering rack ends are the same.
Tighten the tie rod assembly lock nuts.
| *a | Clip Tab Positioning Area |
|
Up |
|
Rear of Vehicle |
Place the steering rack boots on the seats and install the steering rack boot clips.
Make sure that the steering rack boots are not twisted.
Make sure that the tabs of the steering rack boot clip are positioned within the area shown in the illustration.
8.INSPECT WHEEL ANGLE
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of a turning radius gauge.
Turn the steering wheel fully to the left and right and measure the turning angle.
Inspect while the vehicle is unloaded.
If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.
| Engine | SUSPENSION TYPE | Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|---|---|
|
*: for Rough Road Area Specification Vehicles |
||||
| 2AR-FE
A25A-FKS 6AR-FSE |
NORMAL | 205/65R16
215/55R17 |
38°10' +/- 2°00' (38.17° +/- 2.00°)
38°30' +/- 2°00' (38.50° +/- 2.00°)* |
32°45' (32.75°)
33°00' (33.00°)* |
| 235/45R18 | 36°50' +/- 2°00' (36.83° +/- 2.00°)
37°20' +/- 2°00' (37.33° +/- 2.00°)* |
31°50' (31.83°)
32°15' (32.25°)* |
||
| SPORT | - | 36°50' +/- 2°00' (36.83° +/- 2.00°) | 31°55' (31.92°) | |
| 2GR-FKS | NORMAL | 215/55R17 | 38°25' +/- 2°00' (38.42° +/- 2.00°)* | 33°00' (33.00°)* |
| 235/45R18 | 36°45' +/- 2°00' (36.75° +/- 2.00°)
37°05' +/- 2°00' (37.08° +/- 2.00°)* |
31°45' (31.75°)
32°05' (32.08°)* |
||
| SPORT | - | 36°50' +/- 2°00' (36.83° +/- 2.00°) | 31°50' (31.83°) | |
9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
10. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION