Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2018.08–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0319642 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be stored when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the V6 forward recognition camera connector.



B472992E01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-7 (IGB) - V6-10 (GND) LA-P - LA*2
LA-P - W-B*3
Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
V6-1 (HTR)*1 - V6-10 (GND) LA-B - LA*2
LA-B - W*B*3
Camera heater (forward recognition hood) operation signal Ignition switch ON
Camera heater (forward recognition hood) not operating
11 to 14 V
Ignition switch ON
Camera heater (forward recognition hood) operating
Below 1 V
V6-10 (GND) - Body ground LA - Body ground*2
W-B - Body ground*3
Ground Always Below 1 Ω

*1: w/ Camera Heater

*2: excpt RHD without Headup Display

*3: for RHD without Headup Display



b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, malfunction of a CAN bus line, terminating resistor or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-5 (CA1P) - V6-10 (GND) L - LA*1
L - W-B*2
CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
V6-11 (CA1N) - V6-10 (GND) W - LA*1
W - W-B*2
CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
V6-6 (CANH) - V6-10 (GND) G - LA*1
G - W-B*2
CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
V6-12 (CANL) - V6-10 (GND) W - LA*1
W - W-B*2
CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

*1: excpt RHD without Headup Display

*2: for RHD without Headup Display


i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

Waveform 1

Item Content
Terminal Name Between V6-5 (CA1P) and V6-10 (GND)
Between V6-6 (CANH) and V6-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

Waveform 2

Item Content
Terminal Name Between V6-11 (CA1N) and V6-10 (GND)
Between V6-12 (CANL) and V6-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.