There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Headlight ECU sub-assembly LH (w/ Automatic Headlight Beam Level Control System) ·
Headlight ECU sub-assembly RH (w/ Automatic Headlight Beam Level Control System) ·
Outer mirror control ECU assembly (for driver side) (w/ Seat Position Memory System) ·
Outer mirror control ECU assembly (for front passenger side) (w/ Seat Position Memory System) ·
Position control ECU assembly LH (for LHD with Seat Position Memory System) ·
Position control ECU assembly RH (for RHD with Seat Position Memory System) ·
Multiplex tilt and telescopic ECU (w/ Power Tilt and Power Telescopic System) ·
Air conditioning amplifier assembly ·
Certification ECU (smart key ECU assembly) (w/ Smart Entry and Start System) ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Meter mirror sub-assembly (w/ Headup Display System) ·
No. 3 CAN junction connector ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 5 junction connector (for RHD) ·
No. 6 junction connector (for LHD) |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the K126 No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to No. 1 Junction Connector |
| *c | to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System) |
*d | to Combination Meter Assembly |
| *e | to Main Body ECU (Multiplex Network Body ECU) | *f | to Air Conditioning Amplifier Assembly |
| *g | to Headlight ECU Sub-assembly LH
(w/ Automatic Headlight Beam Level Control System) |
*h | to Meter Mirror Sub-assembly
(w/ Headup Display System) |
| *i | to Multiplex Tilt and Telescopic ECU
(w/ Power Tilt and Power Telescopic System) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| K126-3 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 junction connector |
| K126-14 (CANL) - K154-16 (BAT) | |||
| K126-4 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Certification ECU (smart key ECU assembly)*1 |
| K126-15 (CANL) - K154-16 (BAT) | |||
| K126-5 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| K126-16 (CANL) - K154-16 (BAT) | |||
| K126-6 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (multiplex network body ECU) |
| K126-17 (CANL) - K154-16 (BAT) | |||
| K126-7 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| K126-18 (CANL) - K154-16 (BAT) | |||
| K126-8 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Headlight ECU sub-assembly LH*2 |
| K126-19 (CANL) - K154-16 (BAT) | |||
| K126-9 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Meter mirror sub-assembly*3 |
| K126-20 (CANL) - K154-16 (BAT) | |||
| K126-10 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Multiplex tilt and telescopic ECU*4 |
| K126-21 (CANL) - K154-16 (BAT) |
*1: w/ Smart Entry and Start System
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Headup Display System
*4: w/ Power Tilt and Power Telescopic System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 junction connector) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the R94 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 Junction Connector) |
*b | to Outer Mirror Control ECU Assembly (for Driver Side)
(for LHD with Seat Position Memory System) |
| *c | to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for RHD with Seat Position Memory System) |
*d | to No. 3 CAN Junction Connector |
| *e | to No. 6 Junction Connector
(for LHD) |
*f | to No. 5 Junction Connector
(for RHD) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R94-1 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Outer mirror control ECU assembly (for Driver Side)*1 |
| R94-12 (CANL) - K154-16 (BAT) | |||
| R94-1 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Outer mirror control ECU assembly (for front passenger side)*2 |
| R94-12 (CANL) - K154-16 (BAT) | |||
| R94-3 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 3 CAN junction connector |
| R94-14 (CANL) - K154-16 (BAT) | |||
| R94-4 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 6 junction connector*3 |
| R94-15 (CANL) - K154-16 (BAT) | |||
| R94-4 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 5 junction connector*4 |
| R94-15 (CANL) - K154-16 (BAT) |
*1: for LHD with Seat Position Memory System
*2: for RHD with Seat Position Memory System
*3: for LHD
*4: for RHD
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 3 CAN junction connector) | B |
| NG (Line to No. 5 junction connector (for RHD)) | C |
| NG (Line to No. 6 junction connector (for LHD)) | D |
| NG (Line to ECU or sensor) | E |
A
B
C
D
E
Disconnect the R100 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 5 Junction Connector) |
*b | to No. 2 Junction Connector |
| *c | to No. 1 Junction Connector | *d | to Position Control ECU Assembly RH
(w/ Seat Position Memory System) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R100-5 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 2 junction connector |
| R100-16 (CANL) - K154-16 (BAT) | |||
| R100-6 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 junction connector |
| R100-17 (CANL) - K154-16 (BAT) | |||
| R100-7 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Position control ECU assembly RH* |
| R100-18 (CANL) - K154-16 (BAT) |
*: w/ Seat Position Memory System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 junction connector) | B |
| NG (Line to No. 2 junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the R101 No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 Junction Connector) |
*b | to No. 2 Junction Connector |
| *c | to No. 1 Junction Connector | *d | to Position Control ECU Assembly LH
(w/ Seat Position Memory System) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R101-1 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 2 junction connector |
| R101-12 (CANL) - K154-16 (BAT) | |||
| R101-2 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 junction connector |
| R101-13 (CANL) - K154-16 (BAT) | |||
| R101-3 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Position control ECU assembly LH* |
| R101-14 (CANL) - K154-16 (BAT) |
*: w/ Seat Position Memory System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 junction connector) | B |
| NG (Line to No. 2 junction connector) | C |
A
B
C
Disconnect the R97 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 2 Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to No. 6 Junction Connector
(for LHD) |
*d | to No. 5 Junction Connector
(for RHD) |
| *e | to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for LHD with Seat Position Memory System) |
*f | to Outer Mirror Control ECU Assembly (for Driver Side)
(for RHD with Seat Position Memory System) |
| *g | to Headlight ECU Sub-assembly RH
(w/ Automatic Headlight Beam Level Control System) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R97-1 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| R97-12 (CANL) - K154-16 (BAT) | |||
| R97-2 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 6 junction connector*1 |
| R97-13 (CANL) - K154-16 (BAT) | |||
| R97-2 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 5 junction connector*2 |
| R97-13 (CANL) - K154-16 (BAT) | |||
| R97-3 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Outer mirror control ECU assembly (for front passenger side)*3 |
| R97-14 (CANL) - K154-16 (BAT) | |||
| R97-3 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Outer mirror control ECU assembly (for driver side)*4 |
| R97-14 (CANL) - K154-16 (BAT) | |||
| R97-5 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Headlight ECU sub-assembly RH*5 |
| R97-16 (CANL) - K154-16 (BAT) |
*1: for LHD
*2: for RHD
*3: for LHD with Seat Position Memory System
*4: for RHD with Seat Position Memory System
*5: w/ Automatic Headlight Beam Level Control System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 junction connector (for RHD)) | B |
| NG (Line to No. 6 junction connector (for LHD)) | C |
| NG (Line to central gateway ECU (network gateway ECU)) | D |
| NG (Line to ECU or sensor) | E |
A
B
C
D
E
Disconnect the K76 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 2 Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R97-1 (CANH) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| R97-12 (CANL) - K154-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K76-15 (CA5H) - K154-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K76-16 (CA5L) - K154-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG