Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT › 2019.10–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0321092 AUTOMATIC TRANSAXLE UNIT G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35394 1.INSPECT TRANSMISSION OIL CLEANER MAGNET

a.

Examine particles in the automatic transaxle oil pan sub-assembly.

i.
C138722

Collect any steel chips with the removed transmission oil cleaner magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Result:
Steel (magnetic) Brass (non-magnetic)
Bearing, gear and plate wear Bushing wear




Hide 2.INSPECT INPUT SHAFT END PLAY

a.
C136696

Using a dial indicator, measure the input shaft end play.

Standard End Play:

0.020 to 1.242 mm (0.000788 to 0.0488 in.)



Hide 3.INSPECT INTERMEDIATE SHAFT END PLAY

a.
C201496C03
3.025,0.685 3.208,0.85 0.183,0.165 10 *a
*a Dimension (A)


Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.


b.

As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension (A)).


c.
C138268C03
0.589,0.757 0.757,0.936 0.167,0.179 10 *a
*a Dimension (B)


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).


d.

Calculate the end play value using the following formula:

End play = Dimension (B) - Dimension (A) - Thrust needle roller bearing thickness

Standard End Play:

0.022 to 1.099 mm (0.000867 to 0.0432 in.)



Hide 4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C138259

Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear sub-assembly.

Standard Inside Diameter:

25.525 to 25.546 mm (1.00492 to 1.00575 in.)


Maximum Inside Diameter:

25.546 mm (1.00575 in.)


If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.


Hide 5.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201528

Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear assembly.

Standard Inside Diameter:

25.580 to 25.601 mm (1.00708 to 1.00791 in.)


Maximum Inside Diameter:

25.601 mm (1.00791 in.)


If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.


Hide 6.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C200900

Using a feeler gauge, measure the clearance between the underdrive planetary gear assembly and the pinion gear at 4 points.

Standard Clearance:

0.18 to 0.54 mm (0.00709 to 0.0213 in.)


If the clearance is not as specified, replace the underdrive planetary gear assembly.


Hide 7.INSPECT ONE-WAY CLUTCH ASSEMBLY

a.
C189425C03
0.469,1.323 0.469,1.104 0.469,1.104 1.052,0.896 false 2.469,0.802 2.125,0.802 false 2.302,0.281 2.469,0.448 0.167,0.167 10 *b 0.646,0.281 0.823,0.448 0.177,0.167 10 *a 2.51,0.719 2.688,0.885 0.177,0.167 10 *2 0.396,1.323 0.573,1.49 0.177,0.167 10 *1
*1 Planetary Ring Gear
*2 One-way Clutch Assembly
*a Free
*b Lock


Temporarily install the one-way clutch assembly to the planetary ring gear.


b.

Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the one-way clutch assembly does not operate normally, replace it.


Hide 8.INSPECT NO. 1 BRAKE DISC

a.
C203288

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any No. 1 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 1 brake discs.

·

Before assembling new No. 1 brake discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 9.INSPECT NO. 2 BRAKE DISC

a.
C238852

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any No. 2 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 2 brake discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 10.INSPECT NO. 3 BRAKE DISC

a.
C138255

Check if the contact surfaces of the discs, plates and flanges are worn or burnt.

NOTICE:
·

If the lining of any No. 3 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 3 brake discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 11.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C138254

Using a vernier caliper, measure the free length of the 3 2nd brake piston return spring sub-assemblies including the spring seats.

Standard Free Length:

23.26 mm (0.916 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 12.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C141533

Using a vernier caliper, measure the free length of each spring of the 1st and reverse brake return spring sub-assembly including the spring seat.

Standard Free Length:

15.79 mm (0.622 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 13.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C201505

Using a vernier caliper, measure the free length of each spring of the No. 3 brake piston return spring sub-assembly including the spring seat.

Standard Free Length:

9.15 mm (0.360 in.)


If the free length is shorter than the standard free length, replace the No. 3 brake piston return spring sub-assembly.


Hide 14.INSPECT CLEARANCE OF NO. 1 BRAKE

a.
C138258

Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


HINT:

Measure the clearance at 3 points where the No. 1 brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

No. 1 Brake Flange Thickness
Mark Thickness [mm (in.)]
30 3.0 (0.118)
31 3.1 (0.122)
32 3.2 (0.126)
33 3.3 (0.130)
34 3.4 (0.134)
35 3.5 (0.138)
36 3.6 (0.142)


Hide 15.INSPECT CLEARANCE OF NO. 2 BRAKE

a.
C238856

Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard Clearance:

0.707 to 0.974 mm (0.0278 to 0.0383 in.)


HINT:

Measure the clearance at 3 points where the No. 2 brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

No. 2 Brake Flange Thickness
Mark Thickness [mm (in.)]
40A 4.0 (0.157)
41A 4.1 (0.161)
42A 4.2 (0.165)
43A 4.3 (0.169)
44A 4.4 (0.173)
45 4.5 (0.177)
46 4.6 (0.181)
47 4.7 (0.185)


Hide 16.INSPECT CLEARANCE OF NO. 3 BRAKE

a.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the No. 3 brake flange.

C319464C01
0.656,1.656 1.333,1.656 false 2.167,0.979 2.615,0.427 2.615,0.427 2.792,0.427 false 6.083,1.135 6.531,0.583 6.531,0.583 6.708,0.583 false 5.417,1.438 5.417,2.302 false 2.865,0.333 3.177,0.573 0.313,0.24 10 false *1 5.354,2.344 5.74,2.625 0.385,0.281 10 false *2 0.458,1.573 0.802,1.813 0.344,0.24 10 false *3 1.625,0.615 1.958,0.813 0.333,0.198 10 false *a 5.698,1.271 5.958,1.542 0.26,0.271 10 false *b 6.781,0.479 7.073,0.698 0.292,0.219 10 false *c
*1 Front Oil Pump Assembly *2 No. 3 Brake Piston
*3 No. 3 Brake Flange - -
*a Dimension (A) *b Dimension (B)
*c Contact Surface of Front Oil Pump Assembly - -


HINT:

Measure the distance (Dimension(A)) at 3 points where the No. 3 brake flange diameter is approximately 166 mm (6.54 in.) and calculate the average.



b.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

HINT:

Measure the distance (Dimension(B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.



c.

Calculate the clearance using the following formula:

Clearance = Dimension (B) - Dimension (A)

Standard Clearance:

0.599 to 0.799 mm (0.0236 to 0.0315 in.)


If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.


d.

Adjust clearance of No. 3 brake piston:

i.
C317753C01
1.802,1 2.135,1.656 2.135,1.656 2.281,1.656 true 2.323,1.563 2.625,1.875 0.302,0.313 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front oil pump assembly.


ii.
C317765C01
0.75,0.469 1.26,0.469 false 0.563,0.396 0.927,0.76 0.365,0.365 10 false *1
*1 No. 3 Brake Flange


Remove the No. 3 brake flange from the front oil pump assembly.


iii.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the No. 3 brake disc.

C319465C01
0.729,1.688 1.396,1.688 false 2.177,0.979 2.635,0.469 2.635,0.469 2.802,0.469 false 6.073,1.135 6.531,0.625 6.531,0.625 6.698,0.625 false 5.417,1.448 5.417,2.208 false 2.854,0.375 3.177,0.604 0.323,0.229 10 false *1 5.365,2.26 5.688,2.51 0.323,0.25 10 false *2 0.542,1.604 0.854,1.927 0.313,0.323 10 false *3 1.688,0.615 2,0.823 0.313,0.208 10 false *a 5.698,1.25 6,1.542 0.302,0.292 10 false *b 6.771,0.521 7.083,0.792 0.313,0.271 10 false *c
*1 Front Oil Pump Assembly *2 No. 3 Brake Piston
*3 No. 3 Brake Disc - -
*a Dimension (A) *b Dimension (B)
*c Contact Surface of Front Oil Pump Assembly - -


HINT:

Measure the distance (Dimension(A)) at 3 points where the No. 3 brake disc diameter is approximately 166 mm (6.54 in.) and calculate the average.



iv.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

HINT:

Measure the distance (Dimension(B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.



v.

Calculate the thickness of the replacement No. 3 brake flange using the following formula:

Thickness of Replacement No. 3 Brake Flange:

Dimension (B) - Dimension (A) - (0.599 to 0.799 mm (0.0236 to 0.0315 in.))


HINT:

There are 7 No. 3 brake flanges of different thicknesses.


No. 3 Brake Flange Thickness
Mark Thickness [mm (in.)]
38 3.8 (0.150)
39 3.9 (0.154)
40 4.0 (0.157)
41 4.1 (0.161)
42 4.2 (0.165)
43 4.3 (0.169)
44 4.4 (0.173)


vi.
C317765C01
0.75,0.469 1.26,0.469 false 0.563,0.396 0.927,0.76 0.365,0.365 10 false *1
*1 No. 3 Brake Flange


Install the No. 3 brake flange to the front oil pump assembly.


vii.
C274824N07
2.26,0.865 2.667,0.354 2.667,0.354 1.375,0.51 true 2.719,0.26 3.177,0.458 0.458,0.198 10 false A

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the front oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).





Hide 17.INSPECT CLEARANCE OF NO. 1 CLUTCH

a.
C201532

Install the rear multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.


c.
C201533C03
1.094,0.271 1.198,0.271 1.198,0.271 1.406,1.042 false 0.906,0.177 1.135,0.354 0.229,0.177 10 *a
*a Feeler Gauge


Using a feeler gauge, measure the No. 1 clutch pack clearance.

HINT:

Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.


Standard Pack Clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.


Hide 18.INSPECT CLEARANCE OF NO. 2 CLUTCH

a.
C202899

Install the rear multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.


Standard Pack Clearance:

0.394 to 0.605 mm (0.0155 to 0.0238 in.)


If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.